Integrated dynamic brake alerts
Browse 160 IDB alert codes and open an entry for its description and recorded conditions.
IDB alert codes
Showing 101–150 of 160
- IDB_a101 — RCM collision Counter IDB_a101_RCMcollisionCounter RCM collision message RCM_collision counter is incorrect.
- IDB_a102 — Bdw Request Active Invalid IDB_a102_bdwRequestActiveInvalid BDW was continuously requested for more than 10 seconds.
- IDB_a103 — DI full Torque Path Faulted IDB_a103_DIfullTorquePathFaulted The Integrated Dynamic Brake (IDB) will no longer generate system-level brake torques in response to DI_brakeTorqueCommandFull.
- IDB_a104 — DI accel Pos Invalid IDB_a104_DIaccelPosInvalid Invalid DI accel pedal position DI_accelPedalPos is received as Signal Not Available (SNA).
- IDB_a105 — DI gear Invalid IDB_a105_DIgearInvalid Invalid DI gear signal DI_gear is received as Signal Not Available (SNA).
- IDB_a106 — DIF torque Invalid IDB_a106_DIFtorqueInvalid Invalid DIF drive torque signal or qualifier (QF) is received.
- IDB_a107 — DIR torque Invalid IDB_a107_DIRtorqueInvalid Invalid DIR drive torque signal or qualifier (QF) is received.
- IDB_a108 — EPB status DLC IDB_a108_EPBstatusDLC EPB status message EPBL_status was not received or message length is incorrect.
- IDB_a109 — BD Wsignal Invalid IDB_a109_BDWsignalInvalid Invalid BDW request is received.
- IDB_a110 — EPB status Counter IDB_a110_EPBstatusCounter EPB status message EPBL_status counter is incorrect.
- IDB_a111 — EPB status Checksum IDB_a111_EPBstatusChecksum EPB status message EPBL_status checksum is incorrect.
- IDB_a112 — Yaw Rate Invalid IDB_a112_yawRateInvalid Invalid yaw rate signal or qualifier (QF) is received.
- IDB_a113 — Lat Accel Invalid IDB_a113_latAccelInvalid Invalid lateral accel signal or qualifier (QF) is received.
- IDB_a114 — Long Accel Invalid IDB_a114_longAccelInvalid Invalid longitudinal accel signal or qualifier (QF) is received.
- IDB_a115 — VCFRONT esp Lv St Invalid IDB_a115_VCFRONTespLvStInvalid Invalid VCFRONT ESP Low Voltage (LV) state is received.
- IDB_a116 — VCFRONT sensors DLC IDB_a116_VCFRONTsensorsDLC VCFRONT sensors message VCFRONT_sensors was not received or message length is incorrect.
- IDB_a117 — VCLEFT epbm Status DLC IDB_a117_VCLEFTepbmStatusDLC VCLEFT EPBM status message VCLEFT_epbmStatus was not received or message length is incorrect.
- IDB_a118 — VCLEFT epbm Status Counter IDB_a118_VCLEFTepbmStatusCounter VCLEFT EPBM status message VCLEFT_epbmStatus counter is incorrect.
- IDB_a119 — VCLEFT epbm Status Checksum IDB_a119_VCLEFTepbmStatusChecksum VCLEFT EPBM status message VCLEFT_epbmStatus checksum is incorrect.
- IDB_a120 — EPAS3P invalid IDB_a120_EPAS3Pinvalid Invalid EPAS3P steering angle signal qualifier (QF) is received.
- IDB_a121 — Dyno Mode Active IDB_a121_dynoModeActive Dyno mode is activated on the Integrated Dynamic Brake (IDB).
- IDB_a122 — DIF torque Command Invalid IDB_a122_DIFtorqueCommandInvalid Invalid DIF torque command signal is received.
- IDB_a123 — DIR torque Command Invalid IDB_a123_DIRtorqueCommandInvalid Invalid DIR torque command signal is received.
- IDB_a124 — VCFRONT temp Invalid IDB_a124_VCFRONTtempInvalid Invalid VCFRONT tempAmbient signal is received.
- IDB_a125 — PM vdc Cmd State Invalid IDB_a125_PMvdcCmdStateInvalid Invalid Pedal Monitor (PM) VDC signal is received.
- IDB_a126 — DI torque Request Invalid IDB_a126_DItorqueRequestInvalid Invalid Pedal Monitor (PM) PM_state2 message or Drive Inverter (DI) DI_chassisControl message received.
- IDB_a127 — Brake Fluid Level Invalid IDB_a127_brakeFluidLevelInvalid Brake fluid level signal measured by the Integrated Dynamic Brake (IDB) is invalid.
- IDB_a128 — Large Air Volume IDB_a128_largeAirVolume IDB has detected a large air volume in the hydraulic circuit.
- IDB_a129 — RCU input Rod Stroke Invalid IDB_a129_RCUinputRodStrokeInvalid Invalid RCU input rod stroke signal is received.
- IDB_a130 — DI full Torque Request Invalid IDB_a130_DIfullTorqueRequestInvalid Invalid Pedal Monitor (PM) PM_state2 message or Drive Inverter (DI) DI_brakeCommand message received.
- IDB_a131 — Cbc Faulted IDB_a131_cbcFaulted CBC control may be unavailable.
- IDB_a132 — RCU input Rod Stroke QF Invalid IDB_a132_RCUinputRodStrokeQFInvalid Invalid RCU input rod stroke qualifier (QF) is received.
- IDB_a133 — DI brake Command DLC IDB_a133_DIbrakeCommandDLC DI brake command message DI_brakeCommand was not received or message length is incorrect.
- IDB_a134 — DI brake Command Counter IDB_a134_DIbrakeCommandCounter DI brake command message DI_brakeCommand counter is incorrect.
- IDB_a135 — DI brake Command Checksum IDB_a135_DIbrakeCommandChecksum DI brake command message DI_brakeCommand checksum is incorrect.
- IDB_a136 — RCU pts Cal Missing IDB_a136_RCUptsCalMissing The RCU pedal travel sensor offset has not been calibrated.
- IDB_a137 — VCLEFT cdp Request Invalid IDB_a137_VCLEFTcdpRequestInvalid The CDP request is invalid.
- IDB_a138 — DI brake Torque Command And Flag Mismatch IDB_a138_DIbrakeTorqueCommandAndFlagMismatch A non-zero DI_brakeTorqueCommand was received while DI_brakeTorqueRequestActive is 0.
- IDB_a139 — DI brake Torque Command Full SNA IDB_a139_DIbrakeTorqueCommandFullSNA The Integrated Dynamic Brake (IDB) receives an invalid DI_brakeTorqueCommandFull.
- IDB_a140 — PM brake Pedal Cmd QF Invalid IDB_a140_PMbrakePedalCmdQFInvalid Invalid Pedal Monitor (PM) full torque request signal is received.
- IDB_a141 — DI brake Torque Command Full Too Low IDB_a141_DIbrakeTorqueCommandFullTooLow The Integrated Dynamic Brake (IDB) has received a DI_brakeTorqueCommandFull brake torque request that is too low.
- IDB_a142 — PM ebr Cmd State Invalid IDB_a142_PMebrCmdStateInvalid Invalid Pedal Monitor (PM) torque path qualifier (QF) is received.
- IDB_a143 — Factory Mode Active IDB_a143_factoryModeActive IDB is in factory mode for brake fluid filling.
- IDB_a144 — Hydraulic Pushthrough Active IDB_a144_hydraulicPushthroughActive IDB is in hydraulic push-through.
- IDB_a145 — DAS redundant Braking Control DLC IDB_a145_DASredundantBrakingControlDLC DAS brake command message DAS_redundantBrakingControl was not received or message length is incorrect.
- IDB_a146 — DAS redundant Braking Control Counter IDB_a146_DASredundantBrakingControlCounter DAS brake command message DAS_redundantBrakingControl counter is incorrect.
- IDB_a147 — DAS redundant Braking Control Checksum IDB_a147_DASredundantBrakingControlChecksum DAS brake command message DAS_redundantBrakingControl checksum is incorrect.
- IDB_a148 — DAS brake Torque Command Invalid IDB_a148_DASbrakeTorqueCommandInvalid Invalid DAS Redundant Braking Control message received.
- IDB_a149 — DAS mia Brake Torque Command Invalid IDB_a149_DASmiaBrakeTorqueCommandInvalid Invalid DAS Redundant Braking Control message received.
- IDB_a150 — DI loc Status2 DLC IDB_a150_DIlocStatus2DLC DI local status 2 message DI_locStatus2 was not received or message length is incorrect.