Charge port alerts

CP alert codes

Showing 51–100 of 211

• CP_a051 — Door Inductive Sensor MIA CP_a051_doorInductiveSensorMIA The charge port (CP) electronic control unit (ECU) detects that communication with the CP door inductive sensor has failed.
• CP_a052 — Chademo Not Supported CP_a052_chademoNotSupported Vehicle is connected to an offboard CHAdeMO charging station, or CHAdeMO Electric Vehicle Supply Equipment (EVSE), that is not supported.
• CP_a053 — Prox Latched No Pilot CP_a053_proxLatchedNoPilot The charge port (CP) has detected a missing control pilot signal while a charge cable is connected, which usually indicates the charge station does not have power. Charging may not start, and it may be necessary to try a different charge s…
• CP_a054 — Cable Not Secured CP_a054_cableNotSecured Charge port (CP) expects the cable to be secured, but the charge port latch has not secured the cable in place. AC charge rate may be reduced, and DC charging may be unavailable.
• CP_a055 — Charge Stopped No Pilot CP_a055_chargeStoppedNoPilot Control pilot signal from charging station is lost while charging. Charging may be interrupted.
• CP_a056 — Prox Disconnected CP_a056_proxDisconnected Proximity circuit was opened unexpectedly while charging. Charging may be interrupted.
• CP_a057 — Ccs1 Adapter Btn Press CP_a057_ccs1AdapterBtnPress The charge port (CP) detected that button was pressed on the charge cable connected to the Combined Charging System (CCS) Combo 1 Adapter.
• CP_a058 — Ac Charge Retry Pending CP_a058_acChargeRetryPending The charge port (CP) electronic control unit (ECU) will delay an attempt to AC charge
• CP_a059 — Swcan Error CP_a059_swcanError The charge port (CP) electronic control unit (ECU) is unable to establish single wire controller area network (SWCAN) communications.
• CP_a060 — Lost Comms PCS CP_a060_lostCommsPCS The charge port (CP) electronic control unit (ECU) loses communication with the power conversion system (PCS).
• CP_a061 — Uhf Receiver MIA CP_a061_uhfReceiverMIA The charge port (CP) electronic control unit (ECU) detects that the ultra-high frequency (UHF) receiver is missing (MIA).
• CP_a062 — Sc Out Of Service CP_a062_scOutOfService The charge port (CP) electronic control unit (ECU) detects that the vehicle is connected to a Supercharger post that is out of service.
• CP_a063 — Sc Update In Progress CP_a063_scUpdateInProgress The charge port (CP) electronic control unit (ECU) detects that the vehicle is connected to a Supercharger post that is updating.
• CP_a064 — Supercharging Blocked CP_a064_superchargingBlocked The charge port (CP) electronic control unit (ECU) detects that Supercharging is blocked because it is not enabled on the vehicle.
• CP_a065 — Self Test Failed CP_a065_selfTestFailed Manufacturing self test failed
• CP_a066 — Prox Latched Idle Pilot CP_a066_proxLatchedIdlePilot Control pilot signal remains in state B1, indicating the charge station is connected to the vehicle but is not ready to charge the vehicle, for too long while a charge cable is plugged into the charge port (CP). Charging may not start or m…
• CP_a067 — Gbdc Conn Fault CP_a067_gbdcConnFault The charge port (CP) electronic control unit (ECU) detects that a GB (Charging standard used in China) DC charger has an issue with the connector.
• CP_a068 — Door Sensor Mismatch CP_a068_doorSensorMismatch The charge port (CP) electronic control unit (ECU) detects that the presence sensor and potentiometer readings of the CP door position do not match.
• CP_a069 — Door Inductive Sensor Error CP_a069_doorInductiveSensorError The charge port (CP) electronic control unit (ECU) detects a conversion error on the CP door inductive sensor.
• CP_a070 — Door Inductive Sensor Reset CP_a070_doorInductiveSensorReset The charge port (CP) electronic control unit (ECU) reset the CP door inductive sensor due to a I2C communication or conversion error.
• CP_a071 — Exi Decode Failure CP_a071_exiDecodeFailure The charge port (CP) electronic control unit (ECU) is unable to read the received Combined Charging System (CCS) vehicle to grid (V2G) messages.
• CP_a072 — V2g Evcc Timeout CP_a072_v2gEvccTimeout The charge port (CP) electronic control unit (ECU) detects that the charging session is taking longer to startup than expected and exceeds the maximum time frame.
• CP_a073 — Iec Combo Shutdown CP_a073_iecComboShutdown The charge port (CP) electronic control unit (ECU) detects that the Combined Charging System (CCS) charge session was aborted.
• CP_a074 — Failed To Establish V2g Comm CP_a074_failedToEstablishV2gComm The charge port (CP) electronic control unit (ECU) is unable to communicate with the electric vehicle supply equipment (EVSE).
• CP_a075 — V2g Comms Failure CP_a075_v2gCommsFailure The charge port (CP) electronic control unit (ECU) does not receive the expected Combined Charging System (CCS) vehicle to grid (V2G) messages within the expected timeframe.
• CP_a076 — LDC1612error Watchdog CP_a076_LDC1612errorWatchdog Door inductive sensor reporting irrational value
• CP_a077 — Invalid Mac Address CP_a077_invalidMacAddress The charge port (CP) electronic control unit (ECU) detects an invalid MAC address.
• CP_a078 — Latch Not Disengaged Cold CP_a078_latchNotDisengagedCold The charge port (CP) electronic control unit (ECU) detects that the latch is not disengaged when it is expected to be disengaged, and may be frozen.
• CP_a079 — Cable Not Secured Cold CP_a079_cableNotSecuredCold The charge port (CP) electronic control unit (ECU) detects that the charge cable latch is disengaged when it is expected to be engaged, and may be frozen.
• CP_a080 — Task Stack Overflow CP_a080_taskStackOverflow The CP uses this for indicating that a task was detected as overflowing its stack
• CP_a081 — Sw Exception CP_a081_swException The CP uses this for specfic exceptions triggered in code, like data exceptions or machine check errors
• CP_a082 — Power On Reset CP_a082_powerOnReset The charge port (CP) electronic control unit (ECU) detects a reset was completed via a power cycle. This alert is for logging purposes and is set every time a power cycle occurs.
• CP_a083 — Watchdog Trace Data CP_a083_watchdogTraceData The CP uses this to diagnose watchdog resets
• CP_a084 — Prox Pe Disconnected gb CP_a084_proxPeDisconnected_gb The charge port (CP) electronic control unit (ECU) detects that the GB DC or AC protective earth (PE) busbar is missing.
• CP_a085 — Dc Pin Temp Faulted CP_a085_dcPinTempFaulted The charge port inlet pin temperature has reached an unacceptable level (greatly exceeds normal operating range), causing DC charging to stop.
• CP_a086 — Dc Pin Temp Irrational CP_a086_dcPinTempIrrational The charge port (CP) electronic control unit (ECU) detects an open circuit on the DC pin thermistor.
• CP_a087 — Dc Temp Model Fault CP_a087_dcTempModelFault DC pin thermals above model
• CP_a088 — Dc Temp Model Deviation CP_a088_dcTempModelDeviation DC pin thermals above model
• CP_a089 — Plc Config Mismatch CP_a089_plcConfigMismatch The charge port (CP) electronic control unit (ECU) detects that the Gateway (GTW) configuration for power line communication (PLC) does not match the CP ECU hardware configuration.
• CP_a090 — Ccs Evse Low Iso CP_a090_ccsEvseLowIso During a DC fast charging session at a Combined Charging System (CCS) charging station, the electric vehicle supply equipment (EVSE) reports low isolation resistance.
• CP_a091 — Wrong Supercharger Handle CP_a091_wrongSuperchargerHandle The charge port (CP) electronic control unit (ECU) on a combined charging system (CCS) vehicle detects a Supercharger communicating via single-wire controller area network (SWCAN).
• CP_a092 — Modem App Load Failed CP_a092_modemAppLoadFailed The Power Line Communication (PLC) modem application for the Charge Port (CP) electronic control unit (ECU) does not load after a maximum number of automatic retries. DC fast charging will be unavailable at Combined Charging System (CCS) c…
• CP_a093 — Modem Loaded With Reset CP_a093_modemLoadedWithReset The power line communication (PLC) modem successfully booted its application but first required the charge port (CP) electronic control unit (ECU) to reset.
• CP_a094 — Inductive Reset Successful CP_a094_inductiveResetSuccessful The charge port (CP) electronic control unit (ECU) detects communication between the CP ECU and the inductive sensor was successfully recovered via a reset.
• CP_a095 — Thermal Dc Limit Active CP_a095_thermalDcLimitActive The charge port DC pin temperatures have entered a region where its thermal foldback limits are dynamically changing
• CP_a096 — Pilot Wake CP_a096_pilotWake The CP has instigated a wake up event due to pilot
• CP_a097 — Mode Transition Failure CP_a097_modeTransitionFailure The charge port either timed out during a mode request or failed to enter the requested mode
• CP_a098 — Proximity Wake CP_a098_proximityWake The CP has instigated a wake up event due to proximity
• CP_a099 — Cable State Unknown CP_a099_cableStateUnknown The charge port (CP) electronic control unit (ECU) is unable to confirm the state of the charging cable.
• CP_a100 — Inlet Harness Id Irrational CP_a100_inletHarnessIdIrrational The charge port (CP) electronic control unit (ECU) detects unexpected voltage at the inlet harness identifier pins or is unable to identify the type of inlet harness.