The service task reference · 2026
Find the procedure. Understand what it does.
Explore diagnostic tests and repair tasks you can run with Tesware on compatible vehicles.
1,357
service tasks
2026 firmware
Model 3, Y, S & X
1,357 tasks Showing 217–240
Browse by name, A–Z
The procedure clears the media server caches to free up disk space.
PROC_ICE_X_CLEAR-MEDIA-CACHE
This routine will clear the negative pack contactor welded alert, BMS_w/f153_SW_neg_contactor_welded. This routine routine shall ONLY be executed after installing new pack contactors or on rare occasion when instructed to do so by engineering.
PROC_BMS_X_CLEAR-WELDED-NEGATIVE-CONTACTOR-ALERT
This routine will clear the positive pack contactor welded alert, BMS_w/f152_SW_pos_contactor_welded. This routine routine shall ONLY be executed after installing new pack contactors or on rare occasion when instructed to do so by engineering.
PROC_BMS_X_CLEAR-WELDED-POSITIVE-CONTACTOR-ALERT
Clears the load shedding from the Vehicle Controller.
PROC_VCBATT2_X_CLEAR-POST-CRASH-LOADSHEDDING
Clears the load shedding from the Vehicle Front Controller (VCFRONT).
PROC_VCFRONT_X_CLEAR-POST-CRASH-LOADSHEDDING
Clear the Mando Redundant HCU (RCU) Diagnostic Trouble Codes (DTC).
PROC-RCU_X_CLEAR_DTCS
The procedure allows remote Service Alerts and remote notifications to be cleared.
PROC_ICE_X_CLEAR-REMOTE-ALERTS
Clear all right headlamp factory latched faults that were triggering rightHeadlampFactoryFault alert
PROC_VCFRONT_X_CLEAR-RIGHT-HEADLAMP-LATCHED-FACTORY-FAULTS
Clear all right headlamp factory latched faults that were triggering rightHeadlampFactoryFault alert
PROC_VCBATT2_X_CLEAR-HEADLAMP-LATCHED-FACTORY-FAULTS
Executes a routine to clear the side view mirror fold actuator type auto-detected by the Tesla ECU.
PROC_X_CLEAR-MIRROR-FOLD-TYPE
The procedure clears the Spotify cache to free up disk space.
PROC_ICE_X_CLEAR-SPOTIFY-CACHE
The procedure clears existing Spotify credentials.
PROC_ICE_X_CLEAR-SPOTIFY-CREDS
Clears the stored steering wheel haptic motor calibration flag, forcing the system to recalibrate. Use this routine after replacing the steering wheel or haptic motor.
PROC_VCLEFT_X_CLEAR-HAPTIC-CALIBRATION
The procedure clears all updater backups from the Infotainment and Connectivity ECU (ICE). This Task will only run if the filesystem has run out of inodes, otherwise it will cancel.
PROC_ICE_X_CLEAR-UPDATER-BACKUPS
The procedure clears all updater backups from the Infotainment and Connectivity ECU (ICE). This Task will only run if the filesystem has run out of inodes, otherwise it will cancel.
PROC_ICE_X_CLEAR-UPDATER-BACKUPS
Tests communication with the Compressor (CMP) Electronic Control Unit (ECU). Communication is established via Unified Diagnostics Services (UDS) over the Controller Area Network (CAN).
PING-TP_CMP
Tests communication with the Compressor (CMP) Electronic Control Unit (ECU). Communication is established via Unified Diagnostics Services (UDS) over the Controller Area Network (CAN).
PING-TP_CMP
Resets the Compressor (CMP) Electronic Control Unit (ECU). Reset is executed via Unified Diagnostics Services (UDS) over the Controller Area Network (CAN). This routine is only applicable to non-heat pump Model 3 vehicles.
TEST-RESET_CMP
Collects log files from the ICE (Gateway) or APE/APEB (Autopilot) based on specified log paths, then uploads the results to Garage for analysis and/or ticket creation.
PROC_ICE_X_HERMES-GRABLOGS-V2
Used to move the steering column to a target position
PROC_VCLEFT_MOVE-STEERING-COLUMN
Set the compressor to a target speed (800-7000 RPM). If sweep is disabled, the compressor will ramp to target RPM and hold that speed for 15 seconds. If sweep is enabled, the compressor will ramp to target RPM in 500 RPM increments and hold at final target RPM for 15 seconds. Note: The routine may skip some RPM values during sweep, or stop short of the target RPM. This is because some vehicles have certain speeds that are avoided.
PROC_X_COMPRESSOR-RPM-OVERRIDE
Configures connected charger as Master. Script Designed to work together with PROC_CHG_X_CHARGER-STATUS Works only with Gen1 and Gen2 chargers. Before performing configuration; -Enter service mode and perform GTW unlock procedure.
PROC_CHG_X_CHARGER-CONFIG-SET-MASTER
Configures connected charger as Slave. Script Designed to work together with PROC_CHG_X_CHARGER-STATUS Works only with Gen1 and Gen2 chargers. Before performing configuration; -Enter service mode and perform GTW unlock procedure.
PROC_CHG_X_CHARGER-CONFIG-SET-SLAVE
Configure modem ECall for LE940B6-RW Telit modems.
PROC_LTE-MODEM_ECALL-CFG
Descriptions and input definitions come from Tesla’s 2026 vehicle firmware. This catalog includes tasks covered by Tesware’s current service access. Each task page lists the vehicle and firmware versions in which it was found. The connected vehicle confirms whether a task can run.
Cybertruck is not included in this 2026 reference.