The service task reference · 2026
Find the procedure. Understand what it does.
Explore diagnostic tests and repair tasks you can run with Tesware on compatible vehicles.
1,357
service tasks
2026 firmware
Model 3, Y, S & X
1,357 tasks Showing 193–216
Browse by name, A–Z
This routine clears the open voltage sense harness (VSH) alerts BMS_f/w107_SW_Cell_Voltage_Sensor and BMS_f/w177_OpenVshDetected latch bit within the BMS NVRAM. This routine shall ONLY be executed after installing a new/remanufactured HV battery or on rare occasion when instructed to do so by engineering.
PROC_BMS_X_CLEAR-LATCH-BITS
This routine will clear the BMS pack contactor open under load counter. This routine shall ONLY be executed after installing new pack contactors or on rare occasion when instructed to do so by engineering.
PROC_BMS_X_CLEAR-CTC-OPEN-LOAD
This routine will clear the BMS pack contactor stress value for both contactors and in effect, clear BMS_u019_Acceleration_Reduced alert. This routine shall ONLY be executed after installing new pack contactors or on rare occasion when instructed to do so by engineering. See Toolbox Article 32782 for more information.
PROC_BMS_X_CLEAR-CONTACTOR-STRESS
This routine will clear the BMS pack contactors wide open throttle (WOT) counter. This routine shall ONLY be executed after installing new pack contactors or on rare occasion when instructed to do so by engineering.
PROC_BMS_X_CLEAR-CONTACTOR-WOT-COUNTER
This routine clears the BMS SOC1 snapshot which in effect clears all HV battery brick weak short metrics/alerts. This routine shall ONLY be executed after installing a new/remanufactured HV battery or on rare occasion when instructed to do so by engineering. The routine will clear BMS_w117_SW_Delta_SOC_Weak_Short and BMS_u029_dSoc_Limiting if actively set on the vehicle.
PROC_BMS_X_CLEAR-SOC1-SNAPSHOT
Clears cache and temp files located in /home/tesla and /home/mediaserver
PROC_ICE_X_CLEAR-CACHE
The procedure clears the chromium app caches to free up disk space.
PROC_ICE_X_CLEAR-CHROMIUM-CACHE
This task will clear the disable fast charge flag on the charger. This flag can become set if the charger detects low differential resistance on the FC link during the leakage test.
PROC_CHG_X_CLEAR-FAST-CHARGE-DISABLED
The procedure clears Diagnostic Trouble Codes (DTC) in the decoupled pedal brake (DPB) Electronic Control Unit (ECU).
PROC_DPB_X_CLEAR-DTCS
The procedure clears the Drivenotes folder to free up disk space.
PROC_ICE_X_CLEAR-DRIVENOTES
Clears the diagnostic data on the chosen Electronic Control Unit (ECU). This will clear any active Diagnostic Trouble Codes (DTC). DTC functionality may not exist on all ECUs depending on the platform.
PROC_X_CLEAR-DTCS
Restore power for a specific component by clearing its power-off request. Normal power management resumes and the feed turns back on per the vehicle's power state table.
PROC_VC_X_CLEAR-POWER-OFF-REQUEST
Clears Diagnostic Trouble Codes (DTCs) from the electrically assisted power steering (EPAS3P and EPAS3S) electronic control units (ECUs).
PROC_EPAS_X_CLEAR-DTCS
Clear all headlamp factory latched faults that were triggering leftHeadlampFactoryFault and rightHeadlampFactoryFault alerts
PROC_VCFRONT_X_CLEAR-HEADLAMP-LATCHED-FACTORY-FAULTS
Clears the Voltage Sense harness (VSH) alert BMS_a119_Fast_Open_Vsh_Detected latch within the HVBMS NVRAM. This routine shall only be executed after installing a new/remanufactured HV battery.
PROC_HVBMS_X_RESET-VSH-FAULT
Clears the HVC battery coolant flood alert, BMS_a124_Battery_Coolant_Flood, if set. This routine shall only be executed after repairing the HV battery isolation issue.
PROC_HVC_X_CLEAR-BATTERY-COOLANT-FLOOD-ALERT
Clears the HVC internal isolation alert, BMS_a123_SW_Internal_Isolation, if set. This routine shall only be executed after repairing the HV battery isolation issue.
PROC_HVC_X_CLEAR-INTERNAL-ISOLATION-ALERT
Clears the High Voltage Controller (HVC) isolation counters and alerts BMS_a027_SW_Repeated_Isolation_Failure_In_Drive, BMS_a172_SW_Isolation_Failure_In_Drive_Warning, BMS_a123_SW_Internal_Isolation, and BMS_a124_Battery_Coolant_Flood, if set. This routine shall only be executed after repairing a HV system component for loss of isolation.
PROC_HVC_X_CLEAR-ISOLATION-CONDITION
Clears the HVC SOC1 snapshot which in effect clears all HV battery brick weak short calculations and BMS_a029_dSoc_Limiting, if set. This routine shall only be executed after installing a new/remanufactured HV battery.
PROC_HVC_X_CLEAR-SOC1-SNAPSHOT
Clear the Mando Decoupled Brake (IDB) Diagnostic Trouble Codes (DTC).
PROC-IDB_X_CLEAR_DTCS
Clear all left headlamp factory latched faults that were triggering leftHeadlampFactoryFault alert
PROC_VCBATT_X_CLEAR-LEFT-HEADLAMP-LATCHED-FACTORY-FAULTS
Clear all left headlamp factory latched faults that were triggering leftHeadlampFactoryFault alert
PROC_VCFRONT2_X_CLEAR-HEADLAMP-LATCHED-FACTORY-FAULTS
The procedure clears the Lost and Found folder to free up disk space.
PROC_ICE_X_CLEAR-LOST-FOUND
The procedure clears infotainment map cache to free up disk space. Confirm map cache is over 2.1GB.
PROC_ICE_X_CLEAR-MAP-CACHE
Descriptions and input definitions come from Tesla’s 2026 vehicle firmware. This catalog includes tasks covered by Tesware’s current service access. Each task page lists the vehicle and firmware versions in which it was found. The connected vehicle confirms whether a task can run.
Cybertruck is not included in this 2026 reference.