Decoupled power brake alerts

DPB alert codes

Showing 101–150 of 337

• DPB_a101 — Ecu Fast Wd Test Fault DPB_a101_ecuFastWdTestFault Missing Built-In Self Test (BIST) trigger didn't swicth off hydraulically or electrically as expected.
• DPB_a102 — Ecu Vr On While Wd Timeout DPB_a102_ecuVrOnWhileWdTimeout The missing watchdog don't switch off the valve relay.
• DPB_a103 — Ecu Vr Via Spi Fails DPB_a103_ecuVrViaSpiFails The valve relay cannot be switched off via the SPI command of the system IC.
• DPB_a104 — Ecu Wd Startuptest Fault DPB_a104_ecuWdStartuptestFault During failsafe logic test actual and expected WD status of System IC differ.
• DPB_a105 — Ecu Wd S Continuous Error DPB_a105_ecuWdSContinuousError Watchdog status of system IC deviates from the expected one.
• DPB_a106 — Ecu Bist Cmd Test Fault DPB_a106_ecuBistCmdTestFault Contrary to spec Built-In Self Test (BIST) state machine of system IC is started by a wrong BIST command.
• DPB_a107 — Vr On Fails DPB_a107_vrOnFails A switched on valve relay is reported as off (system chip internal status).
• DPB_a108 — GTM Ref Frequency Error DPB_a108_GTMRefFrequencyError GTM reference frequency error.
• DPB_a109 — GTM Tbu Mon Error DPB_a109_GTMTbuMonError GTM reference frequency error.
• DPB_a110 — HWBIST Error DPB_a110_HWBISTError HWBIST detected an error.
• DPB_a111 — Hydraulic Hard Undervoltage DPB_a111_hydraulicHardUndervoltage Hydraulic Hard Undervoltage.
• DPB_a112 — Hydraulic Undervoltage DPB_a112_hydraulicUndervoltage This alert is not valid anymore.
• DPB_a113 — Li PS1 Sent Line High DPB_a113_LiPS1SentLineHigh Linear Position Sensor, Channel 1, line shorted to Supply or Channel 1 Line open or Interruption of Sensor ground.
• DPB_a114 — Li PS1 Sent Line Low DPB_a114_LiPS1SentLineLow Linear Position Sensor, Channel 1, line shorted to ground.
• DPB_a115 — Li PS1 Sent Sensor DPB_a115_LiPS1SentSensor Linear Position Sensor, Channel 1, Sensor internal alert.
• DPB_a116 — Li PS1 Sent Transmission DPB_a116_LiPS1SentTransmission Linear Position Sensor, Channel 1, alert in SENT protocol.
• DPB_a117 — Li PS2 Pwm Line High DPB_a117_LiPS2PwmLineHigh Linear Position Sensor, Channel 2, line shorted to Supply or Channel 2 Line open or Interruption of Sensor ground.
• DPB_a118 — Li PS2 Pwm Line Low DPB_a118_LiPS2PwmLineLow Linear Position Sensor, Channel 2, line shorted to ground.
• DPB_a119 — Li PS2 Pwm Transmission DPB_a119_LiPS2PwmTransmission Linear Position Sensor, Channel 2, Duty or period is out of range.
• DPB_a120 — Li PS Out Of Range High DPB_a120_LiPSOutOfRangeHigh Linear Position Sensor, Out of Range High.
• DPB_a121 — Li PS Out Of Range Low DPB_a121_LiPSOutOfRangeLow Linear Position Sensor, Out of Range Low.
• DPB_a122 — Mic Asic Clk In Error DPB_a122_micAsicClkInError System ASIC CLKIN alert is detected.
• DPB_a123 — Mic Asic Init Test Error DPB_a123_micAsicInitTestError ASIC Init test failed during init task.
• DPB_a124 — Asic Oscillator Error DPB_a124_asicOscillatorError System ASIC internal oscillator alert is detected.
• DPB_a125 — B6 Asic Fault DPB_a125_B6AsicFault Internal bridge driver ASIC hardware defect detected.
• DPB_a126 — MICB6 Transfer Error DPB_a126_MICB6TransferError SPI transfer to Bridge Driver ASIC failed.
• DPB_a127 — Hydraulic Asic Short Circuit DPB_a127_hydraulicAsicShortCircuit Short circuit beteen Qx pin and MRAuC pin are detected.
• DPB_a128 — Mic Spi Transfer Error DPB_a128_micSpiTransferError SPI transfer to System ASIC failed.
• DPB_a129 — Asic Trimming Not Completed DPB_a129_AsicTrimmingNotCompleted System ASIC trimming is not completed.
• DPB_a130 — Asic Malfunction Detected DPB_a130_AsicMalfunctionDetected On the system ASIC an overcurrent event occured. The General Purpose Input Output (GPIO) is not operating as expected.
• DPB_a131 — AS IC Overcurrent On GPIO250 1 DPB_a131_ASICOvercurrentOnGPIO250_1 ASICOvercurrentOnGPIO250 On the system ASIC an overcurrent event occured on GPIO250_1.
• DPB_a132 — AS IC Overcurrent On GPIO250 2 DPB_a132_ASICOvercurrentOnGPIO250_2 ASICOvercurrentOnGPIO250 On the system ASIC an overcurrent event occured on GPIO250_2.
• DPB_a133 — AS IC Overcurrent On GPIO50 1 DPB_a133_ASICOvercurrentOnGPIO50_1 ASICOvercurrentOnGPIO50 On the system ASIC an overcurrent event occured on GPIO50_1.
• DPB_a134 — AS IC Overcurrent On GPIO50 2 DPB_a134_ASICOvercurrentOnGPIO50_2 ASICOvercurrentOnGPIO50 On the system ASIC an overcurrent event occured on GPIO50_2.
• DPB_a135 — AS IC Overcurrent On GPIO50 3 DPB_a135_ASICOvercurrentOnGPIO50_3 ASICOvercurrentOnGPIO50 On the system ASIC an overcurrent event occured on GPIO50_3.
• DPB_a136 — AS IC Overcurrent On GPIO50 4 DPB_a136_ASICOvercurrentOnGPIO50_4 ASICOvercurrentOnGPIO50 On the system ASIC an overcurrent event occured on GPIO50_4.
• DPB_a137 — AS IC Overcurrent On WRHS DPB_a137_ASICOvercurrentOnWRHS On the system ASIC an overcurrent event occured on WRHS.
• DPB_a138 — DI chassis Control Counter DPB_a138_DIchassisControlCounter Alive counter error detected.
• DPB_a139 — DI chassis Control Checksum DPB_a139_DIchassisControlChecksum Checksum error detected.
• DPB_a140 — DI chassis Control DLC DPB_a140_DIchassisControlDLC Data length code error detected.
• DPB_a141 — DI chassis Control Timeout DPB_a141_DIchassisControlTimeout Timeout error detected.
• DPB_a142 — DI system Status Counter DPB_a142_DIsystemStatusCounter Alive counter error detected.
• DPB_a143 — DI system Status Checksum DPB_a143_DIsystemStatusChecksum Checksum error detected.
• DPB_a144 — DI system Status DLC DPB_a144_DIsystemStatusDLC Data length code error detected.
• DPB_a145 — DI system Status Timeout DPB_a145_DIsystemStatusTimeout Timeout error detected.
• DPB_a146 — DIF torque Counter DPB_a146_DIFtorqueCounter Alive counter error detected.
• DPB_a147 — DIF torque Checksum DPB_a147_DIFtorqueChecksum Checksum error detected.
• DPB_a148 — DIF torque DLC DPB_a148_DIFtorqueDLC Data length code error detected.
• DPB_a149 — DIF torque Timeout DPB_a149_DIFtorqueTimeout Timeout error detected.
• DPB_a150 — DIR torque Counter DPB_a150_DIRtorqueCounter Alive counter error detected.