Request Wiper Service Mode
Activates service wiper mode, allowing wiper to be in a service position.
PROC_ICE_X_REQUEST-WIPER-SERVICE-MODE
The service task reference · 2026
Find the procedure. Understand what it does.
Explore diagnostic tests and repair tasks you can run with Tesware on compatible vehicles.
1,357
service tasks
2026 firmware
Model 3, Y, S & X
1,357 tasks Showing 961–984
Browse by name, A–Z
Activates service wiper mode, allowing wiper to be in a service position.
PROC_ICE_X_REQUEST-WIPER-SERVICE-MODE
Turns the drive rail off and attempts to reset all fuses on the EFUSE board.
PROC_EFUSE_X_RESET-EFUSES
Resets Autopilot Air Purge counter back to 0 and clear the associated alert.
PROC_VCFRONT2_X_RESET-AP-AIR-PURGE-COUNTER
Resets Autopilot Air Purge counter back to 0 and clear the associated alert.
PROC_VCFRONT_X_RESET-AP-AIR-PURGE-COUNTER
Send a hard reset ECU command to the BCCEN
TEST-RESET_BCCEN
Run this routine after filter replacement. Resets the Cabin filter health score back to 100%.
PROC_VCRIGHT_X_RESET-CABIN-FILTER-HEALTH
This routine resets all HV battery brick calculated amp-hour capacities (CACs) to their nominal/default values. During normal operation, the BMS calculates brick CAC values over multiple charge/discharge cycles. In the event of a large accumulated error, this routine can reset the calculated CAC based solely on the nominal/default brick CAC values to improve the BMS' full pack energy prediction.
PROC_BMS_X_RESET-CAC
Run this routine after compressor replacement. Resets the compressor power index back to 100.
PROC_VCFRONT2_X_RESET-COMPRESSOR-P-METRIC
Run this routine after compressor replacement. Resets the compressor power index back to 100.
PROC_VCFRONT_X_RESET-COMPRESSOR-P-METRIC
Reset Das A or Das B updater remotely. This is useful for recovering Turbo if it gets stuck during a reboot loop.
PROC_MCU_X_INFO-DAS-UPDATER-RESET
Send a hard reset ECU command to the DI
TEST-RESET_DI
Turns the drive rail off and attempts to reset EFUSE ECU.
PROC_DAS_X_EFUSE-RESET
The procedure resets the User Interface (UI) firmware update progress state.
PROC_ICE_X_RESET-UPDATE-PROGRESS
This routine resets the frunk latch open failure metric alert. Note that the frunk latch open failure metric is only active on single release actuator vehicles.
PROC_VCBATT2_X_RESET-FRUNK-OPEN-FAIL-METRIC
This routine resets the frunk latch open failure metric alert. Note that the frunk latch open failure metric is only active on single release actuator vehicles.
PROC_VCFRONT_X_RESET-FRUNK-OPEN-FAIL-METRIC
Resets the GPS module on the Drivers Assistance (DAS) Electronic Control Unit (ECU).
PROC_DAS-GPS-RESET
Resets HEPA filter health score back to 100% - only run this routine after filter replacement.
PROC_VCRIGHT_X_RESET-HEPA-FILTER-HEALTH
Send a reset ECU command to the LFT (Liftgate controller)
TEST-RESET_LFT
Clears the internal modem reset counter and resets modem via the connectivity stack API.
PROC_ICE_X_MODEM-RESET
Resets Radiator UA index, also known as the "Radiator Health Score" score, back to 100% - only run this routine after performing a radiator cleaning procedure.
PROC_VCFRONT2_RESET-RADIATOR-UA-INDEX
Resets Radiator UA index, also known as the "Radiator Health Score" score, back to 100% - only run this routine after performing a radiator cleaning procedure.
PROC_VC_X_RESET-RADIATOR-UA-INDEX
This routine resets the High Voltage Controller (HVC) life model algorithm to enhance range estimations when an untrustworthy condition is detected. In cases where significant accumulated errors occur, this routine can reset the calculated amp-hour capacity (CAC) and/or life model histogram records, ensuring more accurate range predictions.
PROC_HVC_X_RESET-LIFE-MODEL
CAUTION: reset remote unlock security key on body controller ONLY if remoteAccessRejected alert has fired recently.
PROC_ICE_X_RESET-REMOTE-KEY-SERVICE
The procedure resets ride height calibration values to default.
PROC_TAS_X_RESET-RIDE-HEIGHT-CALIBRATION
Descriptions and input definitions come from Tesla’s 2026 vehicle firmware. This catalog includes tasks covered by Tesware’s current service access. Each task page lists the vehicle and firmware versions in which it was found. The connected vehicle confirms whether a task can run.
Cybertruck is not included in this 2026 reference.