Skip to content
Service procedures 2026 firmware

Reset Range Life Model

Gen3/tasks/PROC_HVC_X_RESET-LIFE-MODEL

Model 3 / YModel S / X (2021+)

What this task does

This routine resets the High Voltage Controller (HVC) life model algorithm to enhance range estimations when an untrustworthy condition is detected. In cases where significant accumulated errors occur, this routine can reset the calculated amp-hour capacity (CAC) and/or life model histogram records, ensuring more accurate range predictions.

Vehicle & firmware coverage

Open a version to see its description, requirements, and input definitions. Hardware configuration and live vehicle checks also determine availability.

Model 3 / Y AMD · Firmware 2026.32.3
Vehicle coverage
2024+ Model 3, 2025+ Model Y, Model Y, Pre-2024 Model 3
Supported connection
Local connection
Vehicle state
Stationary · Parked; Stationary · Neutral
Gateway diagnostic level
Park, Factory, DiagLinkActive, Service

Procedure notes

Resetting the HVC life model will update the estimated range at top of charge, resulting in a more accurate representation of the vehicle's range capability.

Task inputs (0)

No user inputs are listed in this firmware.

Model 3 / Y Intel · Firmware 2026.32.7
Vehicle coverage
Model Y, Pre-2024 Model 3
Supported connection
Local connection
Vehicle state
Stationary · Parked; Stationary · Neutral
Gateway diagnostic level
Park, Factory, DiagLinkActive, Service

Procedure notes

Resetting the HVC life model will update the estimated range at top of charge, resulting in a more accurate representation of the vehicle's range capability.

Task inputs (0)

No user inputs are listed in this firmware.

Model S / X (2021+) AMD · Firmware 2026.20.6.1
Vehicle coverage
2021+ Model S, 2021+ Model X
Supported connection
Local connection
Vehicle state
Stationary · Parked; Stationary · Neutral
Gateway diagnostic level
Park, Factory, DiagLinkActive, Service

Procedure notes

Resetting the HVC life model will update the estimated range at top of charge, resulting in a more accurate representation of the vehicle's range capability.

Task inputs (0)

No user inputs are listed in this firmware.

Related service tasks

Browse all tasks →
Service procedures

After HV Battery Replacement

Before running this routine, a Controller Area Network (CAN) Electronic Control Unit (ECU) redeploy needs to pass. After a High Voltage (HV) Battery replacement, this routine runs all required tasks.

PROC_HVC_X_PACK-REPLACEMENT

Model 3 / Y Model S / X (2021+)
Service procedures

Clear HVC Battery Coolant Flood Alert

Clears the HVC battery coolant flood alert, BMS_a124_Battery_Coolant_Flood, if set. This routine shall only be executed after repairing the HV battery isolation issue.

PROC_HVC_X_CLEAR-BATTERY-COOLANT-FLOOD-ALERT

Model 3 / Y Model S / X (2021+)
Service procedures

Clear HVC Internal Isolation Alert

Clears the HVC internal isolation alert, BMS_a123_SW_Internal_Isolation, if set. This routine shall only be executed after repairing the HV battery isolation issue.

PROC_HVC_X_CLEAR-INTERNAL-ISOLATION-ALERT

Model 3 / Y Model S / X (2021+)
Service procedures

Clear HVC Isolation Condition

Clears the High Voltage Controller (HVC) isolation counters and alerts BMS_a027_SW_Repeated_Isolation_Failure_In_Drive, BMS_a172_SW_Isolation_Failure_In_Drive_Warning, BMS_a123_SW_Internal_Isolation, and BMS_a124_Battery_Coolant_Flood, if set. This routine shall only be executed after repairing a HV system component for loss of isolation.

PROC_HVC_X_CLEAR-ISOLATION-CONDITION

Model 3 / Y Model S / X (2021+)