Find the procedure. Understand what it does.
Explore diagnostic tests and repair tasks you can run with Tesware on compatible vehicles.
1,357
service tasks
Model 3, Y, S & X
857 tasks Showing 145–168
Clear filtersClears the Driver's Assistance System (DAS) calibration data for select camera pairs or all cameras.
PROC_DAS_X_CLEAR-CALIBRATION
Clears the lens hood occlusion alert from the camera health system.
PROC_DAS_X_CLEAR-LENS-HOOD-ALERT
Starts Calibration Mode on the Autopilot Electronic Control Unit (ECU). This routine is required so other routines can be executed.
PROC_DAS_X_ENTER-CALIBRATION-MODE
Updates firmware on selected camera.
PROC_DAS_X_UPDATE-CAMERA
The Ethernet pings Ape-A, Ape-B, or both. After a reply is received, five pings are sent and the full ping output is returned. Make sure to turn on the accessory drive rail. The estimated time to complete is one second per ping line output.
PING_DAS_X_ETHERNET-PING-DAS-ECUS
Checks if the Driver's Assistance System (DAS) Electronic Control Unit (ECU) is connected and powered. Make sure to turn on the accessory drive rail and keep the DAS ECU awake to run the self test successfully.
PING-TP_DAS
Exit calibration mode on the Autopilot Electronic Control Unit (ECU).
PROC_DAS_X_EXIT-CALIBRATION-MODE
Runs diagnostics on ASM330 IMU sensor's accelerometer and gyroscope.
PROC_DAS_X_IMU-CHECK
Resets the Driver's Assistance System (DAS) Electronic Control Unit (ECU) using the Controller Area Network (CAN) bus.
TEST-RESET_DAS
The procedure sends a command to the Driver Assistance System (DAS) Service Application Programming Interface (API) and wakes DAS electronic control unit (ECU) if needed.
PROC_ICE_X_DAS-SERVICE-API
Tests communication of the front left and right Instrument Panel RGB lights (RGBIP) with Left Vehicle Controller (VCLEFT) over the Local Interconnect Network (LIN) bus.
TEST-SELF_VCLEFT_RGBIP
Lists infotainment datavalues. Apply filters in regular expression syntax to narrow the returned list.
TEST-BASH_ICE_X_LIST-DATAVALUES
Tests communication with the Decoupled Pedal Brake (DPB) Electronic Control Unit (ECU). Communication is established via Unified Diagnostics Services (UDS) over the Controller Area Network (CAN).
PING-TP_DPB
Performs a Drive Inverter Front (DIF) restore from the latest application data backup saved onto the car computer. This should only be run after the restore bootloader data routine. Requirements: - New compatible drive inverter is installed. - DIF Bootloader Data Restore routine passed successfully. - DIF software is updated.
PROC_DIF_X_ECU-REPLACEMENT-RESTORE-APP
Saves the bootloader and application data backup snapshot from the Drive Inverter Front (DIF) on the car computer. The backup data is needed when performing a drive inverter replacement.
PROC_DIF_X_ECU-REPLACEMENT-STORE
Sets the usage ID for the Front Drive Inverter (DIF) and restores the bootloader data from the last backup saved onto the car computer. Requirements: - New compatible drive inverter is installed.
PROC_DIF_X_ECU-REPLACEMENT-RESTORE-BOOT
Checks the communication of the Front Drive Inverter (DIF) Electronic Control Unit (ECU). Communication is established through Unified Diagnostics Services (UDS) over the Controller Area Network (CAN). When communication is established, the test will succeed. If the test fails, inspect the wiring and confirm the ECU is powered.
PING-TP_DIF
Resets the Front Drive Inverter (DIF) Electronic Control Unit (ECU). Reset is executed through Unified Diagnostics Services (UDS) over the Controller Area Network (CAN).
TEST-RESET_DIF
Turns on the side and rear view mirrors dimming for two minutes.
PROC_X_FRONT_DIM-MIRRORS
Performs a Drive Inverter Rear (DIR) restore from the latest application data backup saved onto the car computer. This should only be run after the restore bootloader data routine. Requirements: - New compatible drive inverter is installed.
PROC_DIR_X_ECU-REPLACEMENT-RESTORE-APP
This routine saves a PMR and DIR bootloader and application data backup snapshot from the installed drive inverter onto the car computer. The backup data is needed when performing a drive inverter replacement.
PROC_DIR_X_ECU-REPLACEMENT-STORE
This routine sets the usage id for the rear inverter and restores the bootloader data from the latest data backup saved onto the car computer. Requirements: - New compatible drive inverter is installed
PROC_DIR_X_ECU-REPLACEMENT-RESTORE-BOOT
Tests the communication of the Rear Drive Inverter (DIR) Electronic Control Unit (ECU). Communication is established via UDS over the Controller Area Network (CAN). When communication is established, the test will succeed. If the test fails, inspect the wiring and confirm the ECU is powered.
PING-TP_DIR
After replacing the Rear Drive Inverter (DIR), this task restores the bootloader data and configures the Usage ID.
PROC_PMR_X_RESTORE-DATA-BOOT-AND-WRITE-DRIVE-TYPE