Find the procedure. Understand what it does.
Explore diagnostic tests and repair tasks you can run with Tesware on compatible vehicles.
1,357
service tasks
Model 3, Y, S & X
421 tasks Showing 265–288
Clear filtersThis test checks for the presence of the passenger door module at station FL-210 to ensure the connection to the door module is made correctly.
TEST_BCFPM_FRONT-PAS_PRESENCE
Tests the cladding sensor on the passenger Falcon door by monitoring the BCFALCP_stoppingCondition CAN signal.
TEST_BCFALCP_X_CLADDING-SENSOR
Tests the passenger side pinch strip on Falcon doors by monitoring the BCFALCP_pinchStripStatus CAN signal.
PROC_BCFALCP_FALCON-PASS_PINCH-STRIP-NEW
Tests the ultrasonic sensor of the passenger side Falcon door to ensure it is functioning correctly when an obstacle is present.
TEST-SELF_BCFALCP_PAS_USS-ROOF-WITH-OBSTACLE
Read the calibration values of the front door actuator brake. Check Toolbox article #23251 for more details.
PROC_BCFPM_FRONT-PASS_READ-PFD-ACTUATOR-CAL
Write the calibration values of the front door actuator brake. If no values are specified, then default calibration values will be written. Check Toolbox article #23251 for more details. Note: CW = Clock Wise, used by RIGHT side door; CCW = Counter Clock Wise, used by LEFT side door.
PROC_BCFPM_FRONT-PASS_WRITE-PFD-ACTUATOR-CAL
This check verifies that the passenger side mirror is heating when it is commanded on.
PROC_CID_FRONT-PASS_MIRROR-DEFROST
The automated mirror folding routine actuates the mirror through its full range of motion while folding.
PROC_BCFPM_PASS_MIRROR-FOLDING-PS
The automated mirror folding routine actuates the mirror through its full range of motion while folding.
PROC_BCFPM_PASS_MIRROR-TILT-PS
Calibrate the front passenger seat occupancy sensor.
PROC_VCSEATP_FRONT-PASS_OCS-CALIBRATE
This routine performs the VIN Learn, and side configuration learn for Pektron door module. This is necessary to ensure the passenger door controller (PDM) recognizes the correct vehicle configuration. Test will always report as passed to MES due to unreliability of the routine. Routine is necessary after any configuration changes that affect the PDM module.
PROC_PDM_PASS_PEKTRON-VIN-LEARN
Test the functionality of the Pedestrian Warning External Speaker. This is a user-verified acoustic test.
TEST-BASH_CID_X_SPEAKER-EXT-2
Runs the Learn Car routine on Pektron BDY controller. Takes up to 6mins to succeed in normal cases.
PROC_BDY_X_PEKTRON-LEARN-CAR
User initiated check for the interior mechanical door release. The mechanical release on the front door is a cable that is actuated when the interior door handle is pulled back fully. This test only applies to Model X vehicles equipped with LIN controlled cinching latches.
TEST_BCFPM_FRONT-PAS_DOOR-RELEASED
Pings the wireless USB charger
PING-BASH_WIRELESS-CHARGER
This routine will update the PLC Relay configuration
PROC_CP_X_PLC-RELAY-RETROFIT
Tests communication with the PLCRLY Electronic Control Unit (ECU). Communication is established via Unified Diagnostics Services (UDS) over the Controller Area Network (CAN).
PING-TP_PLCRLY
Tests Controller Area Network (CAN) communication with the pedal monitor (PM).
PING-TP_PM
Tests communication with the Pedal Monitor Slave (PMS) Electronic Control Unit (ECU). Communication is established via Unified Diagnostics Services (UDS) over the Controller Area Network (CAN).
PING-TP_PMS
Before executing this routine, a Controller Area Network (CAN) redeploy must pass. After an High Voltage (HV) Battery replacement, this routine runs all required tasks. Execute this routine after installing a HV battery. The first responder loop must be disconnected and the Low Voltage (LV) battery must be connected to a float charger.
PROC_BMS_X_PACK-REPLACEMENT
This routine executes a sequence of actions needed to be taken following a pack contactor replacement. This routine shall ONLY be executed after installing new pack contactors or on rare occasion when instructed to do so by engineering. See Toolbox Article 6864000 for more information.
PROC_BMS_X_CONTACTOR-REPLACEMENT
Provision BCCEN by learning the vehicle vin. Once provisioned, keyfobs will need to be re-paired. If using a keyfob that was previously connected to a vehicle, first use the toolbox3 keyfob pairing tool to unpair and clear personalization.
PROC_BCCEN_X_PROVISIONING
Tests communication with the Cabin Heater (PTC) Electronic Control Unit (ECU). Communication is established via Unified Diagnostics Services (UDS) over the Controller Area Network (CAN).
PING-TP_PTC
Tests communication with the PTCR Electronic Control Unit (ECU). Communication is established via Unified Diagnostics Services (UDS) over the Controller Area Network (CAN).
PING-TP_PTCR