Skip to content

Tesla service tasks.

Find the procedure. Understand what it does. Explore diagnostic tests and repair tasks you can run with Tesware on compatible vehicles.

1,357

service tasks

Model 3, Y, S & X

Find a service task

857 tasks Showing 265–288

Clear filters
Service procedures

Five Way Valve Flow Test

Starts the Thermal Five Way Valve Flow Test. The routine will run for up to 5 minutes.

PROC_VCFRONT_X_THERMAL-FIVE-WAY-VALVE-FLOW-TEST

Model 3 / Y
Service procedures

Five-Way Valve Flow Test - Stop

Stops the thermal five-way coolant valve flow test routine.

PROC_VCFRONT_X_STOP_THERMAL-FIVE-WAY-VALVE-FLOW-TEST

Model 3 / Y
Service procedures

FL and RR Brake Bleed

The Electronic Stability Program (ESP) Hydraulic Control Unit executes the brake fluid flush and bleed process. Active-circuit wheels are Front-Left (FL) and Rear-Right (RR). Use this routine only during fluid flush or bleed with appropriate brake bleeding equipment. The estimated time to complete is five seconds. The ESP Hydraulic Control Unit will run the high pressure pump and control circuit valves to facilitate a prescheduled brake fluid flush or bleed.

PROC_ESP_FRONT-L-REAR-R-BRAKE-BLEED

Model 3 / Y Model S / X (2021+)
Service procedures

Force HVIL Current Source On

Forces the High Voltage Processor (HVP) High Voltage Interlock Loop (HVIL) current source to be on for the specified duration in seconds. When the routine completes, the HVIL current source is no longer being forced on. To end the routine early, perform a Gateway (GTW) reboot through scroll wheel reset."

PROC_HVP_X_FORCE-HVIL-ON

Model 3 / Y Model S / X (2021+)
Service procedures

Force Install Update

The force install update procedure immediately runs a staged firmware update on the vehicle.

PROC_ICE_X_FORCE-INSTALL-UPDATE

Model 3 / Y Model S / X (legacy) Model S / X (2021+)
Service procedures

Force trigger headlight leveling

This routine is used to level headlights according to a LIVE_AX pitch estimate, so that measurements of headlight aim/level can be taken with a gravity-referenced headlight aiming machine (eg, one with a bubble level). Do not use this routine with the wall aiming measurement method.

PROC_VCFRONT_X_TRIGGER-LIVE-AX-HEADLIGHT-LEVELING

Model 3 / Y
Service procedures

Force Updater Handshake

Manually trigger a CID updater handshake with the firmware server

PROC_ICE_X_FORCE-ICE-UPDATER-HANDSHAKE

Model 3 / Y Model S / X (legacy) Model S / X (2021+)
Service procedures

FR and RL Brake Bleed

The Electronic Stability Program (ESP) Hydraulic Control Unit executes the brake fluid flush and bleed process. Active-circuit wheels are Front-Right (FR) and Rear-Left (RL). Use this routine only during fluid flush or bleed with appropriate brake bleeding equipment. The estimated time to complete is five seconds. The ESP Hydraulic Control Unit will run the high pressure pump and control circuit valves to facilitate a prescheduled brake fluid flush or bleed.

PROC_ESP_FRONT-R-REAR-L-BRAKE-BLEED

Model 3 / Y Model S / X (2021+)
Service procedures

FRONT CAMERA HAZE & STREAK CHECK

Captures RAW images from the APE and runs haze & streak detection using the factory camera check application.

PROC_ICE_X_CAMERA-FISHEYE-CLEANLINESS

Model 3 / Y
Service procedures

FRONT CAMERA HAZE CHECK

Captures RAW images form the APE and runs haze/offgassing detection using the factory camera check application.

PROC_ICE_X_CAMERA-FISHEYE-HAZE

Model 3 / Y
Service procedures

FRONT CAMERA STREAK CHECK

Captures RAW images form the APE and runs streak detection using the factory camera check application.

PROC_ICE_X_CAMERA-FISHEYE-STREAK

Model 3 / Y
Communication checks

Front Cameras Connection Test

Tests main camera connection and performs camera firmware update.

PING-HTTP_DAS_X_MAIN-CAMERA-SCRIPT

Model 3 / Y Model S / X (2021+)
Service procedures

Front Controller Post-Replacement Procedure

Consolidates all of the required ODIN routines after replacing the Front Vehicle Controller (VCFRONT).

PROC_VCFRONT_X_POST-REPLACEMENT-PROCEDURE

Model 3 / Y Model S / X (2021+)
Service procedures

Front Drive Unit Resolver Error Learning

Calibrates the resolver analog input error, which is required after an inverter swap. Before running this routine, confirm the steering wheel is straight and the drive rail is on. Run this routine while the vehicle is on the lift. After starting the routine, follow these steps to complete inverter replacement: 1. Shift into Drive within 10 seconds of starting the routine, and firmly press the accelerator pedal. 2. Keep the accelerator pedal pressed until the motor starts slowing down on its own. 3. Press the brake and shift into Park after the speedometer reaches 0. Do not press the brake pedal during coast down. Brake softly to cancel the routine.

PROC_DIF_X_RESOLVER-ERROR-LEARN

Model 3 / Y Model S / X (2021+)
Self-tests

Front Fog and Side Markers Test for both NA and EU

Tests for power, connection, and communication of the front fog light and side marker lights controlled by the Front Vehicle Controller (VCFRONT).

TEST-SELF_VCFRONT_FRONT_FOG-SIDE-MARKERS

Model 3 / Y Model S / X (2021+)
Self-tests

Front Left Door RGB light LIN connection test

Tests communication of the Front Left Door RGB light (RGBDOORFL) with Left Vehicle Controller (VCLEFT) over the Local Interconnect Network (LIN) bus.

TEST-SELF_VCLEFT_RGBDOORFL

Model 3 / Y
Self-tests

Front Left Seat Lumbar Test

Tests for power, connection, and communication of the front left seat lumbar controlled by the Left Vehicle Controller (VCLEFT).

TEST-SELF_VCLEFT_FRONT-L_SEAT-LUMBAR

Model 3 / Y Model S / X (2021+)
Self-tests

Front Left Window Calibration

Calibrates front left window endstops for pinch detection. Ensure the front left door is closed. Do not open the door or press the window switch button while the routine runs.

TEST-SELF_VCLEFT_FRONT-L_CALIBRATE-WINDOW

Model 3 / Y Model S / X (2021+)
Diagnostic tests

Front Left Woofer Connection Test

Checks the electrical connection of the front left woofer of the premium speaker.

TEST-BASH_SPK-PREM_FRONT-L_WOOFER

Model 3 / Y
Service procedures

Front Only Motor Mode

Enables only the front motor on a dual-motor vehicle with All-Wheel Drive (AWD). Vehicle will operate with only the front motor. To run this procedure, vehicle must be AWD and either GUI_isDevelopmentCar, GUI_factoryMode, or GUI_serviceMode must be set to 'True'.

PROC_ICE_X_FRONTONLY-MOTOR-MODE

Model 3 / Y Model S / X (legacy) Model S / X (2021+)
Self-tests

Front Right Door RGB light LIN connection test

Tests communication of the Front Right Door RGB light (RGBDOORFR) with Right Vehicle Controller (VCRIGHT) over the Local Interconnect Network (LIN) bus.

TEST-SELF_VCRIGHT_RGBDOORFR

Model 3 / Y