Find the procedure. Understand what it does.
Explore diagnostic tests and repair tasks you can run with Tesware on compatible vehicles.
1,357
service tasks
Model 3, Y, S & X
665 tasks Showing 577–600
Clear filtersThis is a user verified check to verify function of the steering heater. The user should pass the test if the steering heater is functioning when triggered on.
PROC_CID_X_STEERING-HEATER
This test turns the steering heater off.
PROC_CID_X_STEERING-HEATER-OFF
Run this routine after retrofitting the wheel type in any manner. Sets the steering wheel configuration based on the installed part number. Note: Model S/X Long Range built after 8 MAY 2025 do not support yoke; only ROUND or ROUND_MECHANICAL_HORN selections are accepted on those vehicles. Plaid variants are unaffected.
PROC_GTW_X_STEERING-WHEEL-YOKE-SWAP
Stops the High Voltage (HV) Battery discharge routine, if active.
PROC_VCFRONT2_X_HV-DISCHARGE-STOP
Stops the High Voltage (HV) Battery discharge routine, if active.
PROC_VCFRONT_X_HV-DISCHARGE-STOP
Asks sunroof to stop moving.
PROC_CID_X_SUNROOF-STOP
The procedure stops the Close Refrigerant Valves routine and returns results.
PROC_VCFRONT2_X_STOP-CLOSE-REFRIGERANT-VALVES
The procedure stops the Close Refrigerant Valves routine and returns results.
PROC_VCFRONT_X_STOP-CLOSE-REFRIGERANT-VALVES
The procedure stops the Thermal Coolant Flow Cycle with all coolant modes.
PROC_VCFRONT2_X_STOP-THERMAL-COOLANT-FLOW-CYCLE
The procedure stops the Thermal Coolant Flow Cycle with all coolant modes.
PROC_VCFRONT_X_STOP-THERMAL-COOLANT-FLOW-CYCLE
Stops the Thermal Fluid Fill and Thermal Fluid Drain routine, allowing the coolant valve, coolant pumps, and Electronic Expansion Valves (EXVs) to return to their default operational states.
PROC_VCFRONT2_X_STOP-THERMAL-FILL-DRAIN
Stops the Thermal Fill and Drain routine and allows the coolant valve, coolant pumps, and Electronic Expansion Valves (EXVs) to return to their default operational states.
PROC_VCFRONT_X_STOP-THERMAL-FILL-DRAIN
Store drive INVERTER bootloader and application data before replacement
PROC_PMX_X_STORE-ALL-DATA-AWD
Store drive INVERTER bootloader and application data before replacement
PROC_PMX_X_STORE-ALL-DATA-AWD-OR-AWD-DUAL-REAR
Backs up Rear Left Drive Inverter (DIREL) bootloader data. Press the brake pedal to turn on drive rail before starting the routine.
PROC_PMREL_X_STORE-DATA-BOOT
This routine stores the Rear Right Drive Inverter Bootloader Data before replacement. Press the brake pedal to turn on drive rail before starting the routine.
PROC_PMRER_X_STORE-DATA-BOOT
This routine performs the VIN Learn, and side configuration learn for Pektron door module. This is necessary to ensure the sunroof controller (SUN) recognizes the correct vehicle configuration. Test will always report as passed to MES due to unreliability of the routine. Routine is necessary after any configuration changes that affect the SUN module.
PROC_SUN_X_PEKTRON-VIN-LEARN
Runs the sv command on the car computer to control and see the current status of infotainment processes.
PROC_ICE_X_SV-COMMAND
The dual bootstrap eSim procedure swaps the eSim operator from AT&T to KPN and vice-versa. For the procedure to execute properly, the 'kpn' input must be set to 'true' to switch to KPN and 'false' to switch to AT&T.
PROC_ICE_X_DUAL-BOOTSTRAP-E-SIM
The procedure assists the inflation of a component on a Tesla Air Suspension (TAS) vehicle.
PROC_TAS_X_ASSISTED-INFLATE
The procedure clears crash detection alerts in the Tesla Air Suspension (TAS) ECU.
PROC_TAS_X_CLEAR-CRASH-DETECTED
The procedure clears spring leakage alerts in the Tesla Air Suspension (TAS) ECU.
PROC_TAS_X_CLEAR-SPRING-LEAK-ALERT
Deflates a component on the Tesla Air Suspension (TAS) system. Tesla Air Suspension (TAS) Electronic Control Unit (ECU) must be in Service Mode to run the procedure.
PROC_TAS_X_DEFLATE
Levels the Tesla Air Suspension (TAS) to the selected target height.
PROC_TAS_X_LEVEL-TO-HEIGHT