Find the procedure. Understand what it does.
Explore diagnostic tests and repair tasks you can run with Tesware on compatible vehicles.
1,357
service tasks
Model 3, Y, S & X
665 tasks Showing 385–408
Clear filtersLearns the Vehicle Identification Number (VIN) to the Bosch PARK 4.5 Module. This routine is required when the module is replaced.
PROC_PARK_X_BOSCH45-VIN-LEARN
This action will update Passenger Airbag Type Configuration on the vehicle. If the Safety_Vent does not appear in garage for cfg_passengerairbagtype after the reboot, leave and lock the vehicle to initiate another reboot.
PROC_PAB_X-RETROFIT
Tests the passenger side pinch strip on Falcon doors by monitoring the BCFALCP_pinchStripStatus CAN signal.
PROC_BCFALCP_FALCON-PASS_PINCH-STRIP-NEW
Read the calibration values of the front door actuator brake. Check Toolbox article #23251 for more details.
PROC_BCFPM_FRONT-PASS_READ-PFD-ACTUATOR-CAL
Write the calibration values of the front door actuator brake. If no values are specified, then default calibration values will be written. Check Toolbox article #23251 for more details. Note: CW = Clock Wise, used by RIGHT side door; CCW = Counter Clock Wise, used by LEFT side door.
PROC_BCFPM_FRONT-PASS_WRITE-PFD-ACTUATOR-CAL
Increases the force required to close the passenger front door for the BCFPM ECU.
PROC_BCFPM_FRONT-PAS-PFD-SET-CLOSE-CALIBRATION-HEAVIER
Decreases the force required to close the passenger front door for the BCFPM ECU.
PROC_BCFPM_FRONT-PAS-PFD-SET-CLOSE-CALIBRATION-LIGHTER
Increases the force required to open the passenger front door for the BCFPM ECU.
PROC_BCFPM_FRONT-PAS-PFD-SET-OPEN-CALIBRATION-HEAVIER
Decreases the force required to open the passenger front door for the BCFPM ECU.
PROC_BCFPM_FRONT-PAS-PFD-SET-OPEN-CALIBRATION-LIGHTER
This check verifies that the passenger side mirror is heating when it is commanded on.
PROC_CID_FRONT-PASS_MIRROR-DEFROST
Executes a routine to fold the Passenger mirror
PROC_BCFPM_MIRROR-FOLD
The automated mirror folding routine actuates the mirror through its full range of motion while folding.
PROC_BCFPM_PASS_MIRROR-FOLDING-PS
The automated mirror folding routine actuates the mirror through its full range of motion while folding.
PROC_BCFPM_PASS_MIRROR-TILT-PS
Executes a routine to unfold the Passenger mirror
PROC_BCFPM_MIRROR-UNFOLD
Calibrates the front passenger seat.
PROC_VCSEATP_SEAT-CALIBRATE
Calibrate the front passenger seat occupancy sensor.
PROC_VCSEATP_FRONT-PASS_OCS-CALIBRATE
This routine performs the VIN Learn, and side configuration learn for Pektron door module. This is necessary to ensure the passenger door controller (PDM) recognizes the correct vehicle configuration. Test will always report as passed to MES due to unreliability of the routine. Routine is necessary after any configuration changes that affect the PDM module.
PROC_PDM_PASS_PEKTRON-VIN-LEARN
Runs the Learn Car routine on Pektron BDY controller. Takes up to 6mins to succeed in normal cases.
PROC_BDY_X_PEKTRON-LEARN-CAR
Actuates the Plaid drive unit oil pumps for draining the gearbox fluid.
PROC_DIREL_X_OIL-PUMP-DRAIN-CONTROL
Actuates the Plaid drive unit oil pumps for filling the gearbox fluid.
PROC_DIREL_X_OIL-PUMP-FILL-CONTROL
This routine will update the PLC Modem configuration
PROC_CP_X_PLC-MODEM-RETROFIT
This routine will update the PLC Relay configuration
PROC_CP_X_PLC-RELAY-RETROFIT
Before executing this routine, a Controller Area Network (CAN) redeploy must pass. After an High Voltage (HV) Battery replacement, this routine runs all required tasks. Execute this routine after installing a HV battery. The first responder loop must be disconnected and the Low Voltage (LV) battery must be connected to a float charger.
PROC_BMS_X_PACK-REPLACEMENT
This routine executes a sequence of actions needed to be taken following a pack contactor replacement. This routine shall ONLY be executed after installing new pack contactors or on rare occasion when instructed to do so by engineering. See Toolbox Article 6864000 for more information.
PROC_BMS_X_CONTACTOR-REPLACEMENT