Skip to content

Tesla service tasks.

Find the procedure. Understand what it does. Explore diagnostic tests and repair tasks you can run with Tesware on compatible vehicles.

1,357

service tasks

Model 3, Y, S & X

Find a service task

421 tasks Showing 169–192

Clear filters
Service procedures

Fuse Modem

The procedure fuses only the modem board when the other components are already fused. This is useful for modem replacements that were not fused in the factory. Production components should always be fused.

PROC_SEC_X_FUSE-MODEM

Model 3 / Y Model S / X (legacy) Model S / X (2021+)
Service procedures

Gen2 GTW Configuration Update

Updates the configuration for the Gen 2 Gateway (GTW).

PROC_ICE_X_ACCESS-INTERNAL-DAT

Model S / X (legacy)
Communication checks

Generic ECU CAN Communication

Tests communication with an Electronic Control Unit (ECU) selected by the user. Communication is established via Unified Diagnostics Services (UDS) over the Controller Area Network (CAN) and confirming a response within 5 seconds.

PING-TP_ECU

Model 3 / Y Model S / X (legacy) Model S / X (2021+)
Service procedures

Get sunroof status

Provides information on current sunroof status.

PROC_CID_X_SUNROOF-STATUS

Model S / X (legacy)
Service procedures

Glass Defrost Off

This test turns all glass defrosts off.

PROC_CID_X_GLASS-DEFROST-OFF

Model S / X (legacy)
Service procedures

Glovebox Open

Opens the glovebox and bypasses glovebox pin.

PROC_ICE_X-OPEN-GLOVEBOX

Model 3 / Y Model S / X (legacy) Model S / X (2021+)
Diagnostic tests

GPS Status

Check the GPS antenna status to be Normal.

TEST_CID_X_GPS

Model S / X (legacy)
Service procedures

GTW Standby Reboot

Requests Gateway (GTW) and User Interface (UI) reboot once vehicle is parked and displays are off.

PROC_ICE_X_STANDBY-REBOOT-GTW

Model 3 / Y Model S / X (legacy) Model S / X (2021+)
Service procedures

iBooster Initialization

Check pedal resting position within tolerance and learn VIN

PROC_IBST_X_IBST-PEDAL

Model S / X (legacy)
Communication checks

IBST CAN Communication

Tests communication with the iBooster (IBST) Electronic Control Unit (ECU). Communication is established via Unified Diagnostics Services (UDS) over the Controller Area Network (CAN).

PING-TP_IBST

Model S / X (legacy)
Diagnostic tests

IBST Stiffness Test Verification

Verifies the brake hydraulic system stiffness. The pressure leakage threshold should be left blank for five seconds.

TEST_BRAKE_X_STIFFNESS-TEST-PRESSURE-BURNISHED

Model S / X (legacy)
Communication checks

IC CAN Communication

Tests communication with the IC Electronic Control Unit (ECU). Communication is established via Unified Diagnostics Services (UDS) over the Controller Area Network (CAN).

PING-TP_IC

Model S / X (legacy)
Service procedures

ICE Enter Autopilot Retrofit Mode

The enter Autopilot Retrofit Mode procedure allows for internet communication on Hardware 3 (HW3) Autopilot electronic control units (ECUs).

PROC_ICE_X_ENTER-RETROFIT-MODE

Model 3 / Y Model S / X (legacy) Model S / X (2021+)
Diagnostic tests

ICE SX Read Gateway Configs

The procedeure reads the full configuration file on the gateway. These settings represent hardware features on the vehicle, such as roof glass and battery variant, in addition to paid features like Autopilot. This Task is similar to Teleforce 'dgc'. It reads directly from the gateway and may be trusted as the best point of reference.

TEST-BASH_ICE_X_READ-SX-GW-CFG

Model S / X (legacy)
Service procedures

Immobilizer Reset

This routine is used to reset the drive unit immobilizer key. This re-learns the code that pairs the drive unit with the security controller (BCCEN). This routine needs to be performed when either the security controller is replaced or the drive unit is permanently removed from a vehicle.

PROC_BCCEN_X_IMMOBILIZER-RESET

Model S / X (legacy)
Service procedures

Immobilizer Reset Procedure

This routine can be used to reset the drive unit immobilizer to the virgin state. This unlearns the code that pairs a drive unit to the security controller. This routine needs to be performed when either the security controller is replaced or the drive unit is permanently removed from a vehicle. Immobilizer reset takes 15 minutes. During this time, DI_immobilizerState will be in RESET, and at the end of the procedure it will become DISARMED. Drive rail must remain on throughout the entire procedure. When the immobilizer reads "Disarmed", the drive unit can be paired with the security controller the next time it is powered on.

PROC_DI_X_IMMOBILIZER-RESET

Model S / X (legacy)
Service procedures

Infotainment System Reboot

Requests infotainment system reboot. Gateway (GTW) does not reboot.

PROC_ICE_X_REBOOT

Model 3 / Y Model S / X (legacy) Model S / X (2021+)
Service procedures

Install Firmware Update

The procedure runs a staged firmware update after 120 seconds.

PROC_ICE_X_INSTALL-UPDATE

Model 3 / Y Model S / X (legacy) Model S / X (2021+)
Diagnostic tests

INTER_DOOR_RELEASE_DRIVER_FRONT

User initiated test to check that the interior electrical door switch is working properly.

TEST_DDM_FRONT-DRV_INTER-DOOR-RELEASE

Model S / X (legacy)