Find the procedure. Understand what it does.
Explore diagnostic tests and repair tasks you can run with Tesware on compatible vehicles.
1,357
service tasks
Model 3, Y, S & X
857 tasks Showing 169–192
Clear filtersResets the Rear Drive Inverter (DIR) Electronic Control Unit (ECU). Reset is executed through Unified Diagnostics Services (UDS) over the Controller Area Network (CAN). inverter (DIR) Electronic Control Unit (ECU).
TEST-RESET_DIR
Lists the files in a given directory on the car computer. This routine is flexible and may be used to explore the filesystem, but not all directories are readable. The filter input can be used to limit the results. For example, listing everything in /dev may yield over 400 results but filtering for 'mmcblk' will only show eMMC devices.
TEST-BASH_ICE_X_LS
Disable 2Row Left Pitch
PROC_VCLEFT_L_EASY-ENTRY-PITCH-DISABLE
Disable 2Row Right Pitch
PROC_VCRIGHT_R_EASY-ENTRY-PITCH-DISABLE
Disables adaptive PLG control
PROC_VCLEFT_X_DISABLE-ADAPTIVE-LIFTGATE-CONTROL
Disable running of Low Voltage Protection Self Tests in the factory.
PROC_VCBATT1_X_DISABLE-FACTORY-LV-PROTECTION-SELF-TESTS
Disable Integrated Dynamic Brake (IDB) leak protection mode
PROC_IDB_DISABLE-LEAK-PROTECTION
Disarms the Restraints Control Module (RCM)
PROC_RCM_DISARM
Lists the amount of free disk space on each partition.
TEST-BASH_ICE_X_DF
Checks disk usage in a list of paths. Use this task when the filesystem is running low on free disk space (see Disk Space Check). The results include a number in Megabytes for each directory.
TEST-BASH_ICE_X_CHECK-DISK-USAGE
Runs the display cable stress test script on the vehicle to diagnose a center display that has a flickering screen and is unresponsive to touch. The estimated time to complete is 40 seconds.
TEST-BASH_ICE_X_DISPLAY-CABLE-STRESS-TEST
Tests power and connection of the center display. Communication is established via either display port or High-Definition Multimedia Interface (HDMI).
PING-BASH_DISPLAY
Request that the Power Manager turns the display off.
PING-BASH_DISPLAY_POWER_OFF
Requests that the Power Manager turns the display on.
PING-BASH_DISPLAY_POWER_ON
The procedure generates a system report that displays memory, Central Processing Unit (CPU), task and swap utilization followed by currently running tasks. This is useful for checking a process for excessive memory or CPU usage.
TEST-BASH_ICE_X_TOP
ALWAYS RUN AFTER BLEED! Used to check for air or leakage in the DPB
TEST-SELF_DPB_LEAKAGE-AND-AIR-MONITORING
This will test the DPB connection to the ESP as well as potential leakage air in the system
TEST-SELF_DPB_AIR-AND-LEAKAGE
Routine to bleed the DPB and/or ESP hydraulic circuit
PROC_DPB_ESP_REPAIR-BLEED
Selftest to perform automatic brake fluid change
PROC_DPB_BRAKE-FLUID-CHANGE
Validates all 4 brake lines by measuring DPB plunger stroke values and validating that none are blocked, have air or leakage
TEST-SELF_BRAKE_X_DPB-ESP-SYSTEM-CHECK
Applies pressure to each individual corner in turn to compare the output values and validate the brakes. If executing with DIAG_LINK_ACTIVE then EPBs will release one at a time, which is required if CHECK_SWAPPED_REAR_LINES is true.
TEST-SELF_BRAKE_X_DPB-ESP-CORNER-STIFFNESS-TEST
Routine to activate or de-activate the assembly mode on DPB
PROC_DPB_X_ASSEMBLY-MODE
Applies pressure to each individual corner in turn to compare the output values and validate the brakes. If executing with DIAG_LINK_ACTIVE then EPBs will release one at a time, which is required if CHECK_SWAPPED_REAR_LINES is true.
TEST-SELF_BRAKE_X_DPB-ESP-CHECK-REAR-CROSSED-LINES
DPB Tandem Master Cylinder test. Do not press for the predaly before the test starts. A small "click" can be heard once the pedal is ready to be pressed.
TEST-SELF_DPB_TMC-BRAKE-PEDAL-PRESS