Refrigerant EXV Test
Model 3 Non-heat-pump ONLY - Refrigerant EXV Test
TEST-SELF_VCFRONT_X_CHILLER-EXV
Find the procedure. Understand what it does.
Explore diagnostic tests and repair tasks you can run with Tesware on compatible vehicles.
1,357
service tasks
Model 3, Y, S & X
857 tasks Showing 577–600
Clear filtersModel 3 Non-heat-pump ONLY - Refrigerant EXV Test
TEST-SELF_VCFRONT_X_CHILLER-EXV
Tests for power, connection, and communication of the refrigerant liquid sensor controlled by the Front Vehicle Controller (VCFRONT2).
TEST-SELF_VCFRONT2_X_REFRIGERANT-LIQUID
Tests for power, connection, and communication of the refrigerant liquid sensor controlled by the Front Vehicle Controller (VCFRONT).
TEST-SELF_VCFRONT_X_REFRIGERANT-LIQUID
Tests for power, connection, and communication of the refrigerant suction sensor controlled by the Front Vehicle Controller (VCFRONT2).
TEST-SELF_VCFRONT2_X_REFRIGERANT-SUCTION
Tests for power, connection, and communication of the refrigerant suction sensor controlled by the Front Vehicle Controller (VCFRONT).
TEST-SELF_VCFRONT_X_REFRIGERANT-SUCTION
Clears current EPBL config and learns new config from gtw car configs. Only use after replacing EPB hardware where gtw config change was required.
PROC_EPBL_CLEAR-BRAKE-HW-TYPE
Clears current EPBR config and learns new config from gtw car configs. Only use after replacing EPB hardware where gtw config change was required.
PROC_EPBR_CLEAR-BRAKE-HW-TYPE
Provides RMI (Repair and Maintenance Information) Vitals values, including configuration values, alerts, and data.
PROC_ICE_X_RMI-VITALS
Requests the accessory rail and the drive rail to power off.
PROC_CID_X_REQUEST-RAILS-OFF
Request accessory power from the vehicle to wake up certain ECU's for a user specified number of seconds.
PROC_ICE_X_REQUEST-ACC-POWER
Turn off HVAC, equivalent to touching the power icon on the UI
PROC_ICE_X_REQUEST-HVAC-OFF
Requests the drive rail to power off and the high voltage battery pack contactors to open.
PROC_CID_X_REQUEST-HV-CONTACTORS-OPEN
Activates service wiper mode, allowing wiper to be in a service position.
PROC_ICE_X_REQUEST-WIPER-SERVICE-MODE
Resets Autopilot Air Purge counter back to 0 and clear the associated alert.
PROC_VCFRONT2_X_RESET-AP-AIR-PURGE-COUNTER
Resets Autopilot Air Purge counter back to 0 and clear the associated alert.
PROC_VCFRONT_X_RESET-AP-AIR-PURGE-COUNTER
Run this routine after filter replacement. Resets the Cabin filter health score back to 100%.
PROC_VCRIGHT_X_RESET-CABIN-FILTER-HEALTH
Run this routine after compressor replacement. Resets the compressor power index back to 100.
PROC_VCFRONT2_X_RESET-COMPRESSOR-P-METRIC
Run this routine after compressor replacement. Resets the compressor power index back to 100.
PROC_VCFRONT_X_RESET-COMPRESSOR-P-METRIC
Reset Das A or Das B updater remotely. This is useful for recovering Turbo if it gets stuck during a reboot loop.
PROC_MCU_X_INFO-DAS-UPDATER-RESET
The procedure resets the User Interface (UI) firmware update progress state.
PROC_ICE_X_RESET-UPDATE-PROGRESS
This routine resets the frunk latch open failure metric alert. Note that the frunk latch open failure metric is only active on single release actuator vehicles.
PROC_VCBATT2_X_RESET-FRUNK-OPEN-FAIL-METRIC
This routine resets the frunk latch open failure metric alert. Note that the frunk latch open failure metric is only active on single release actuator vehicles.
PROC_VCFRONT_X_RESET-FRUNK-OPEN-FAIL-METRIC
Resets the GPS module on the Drivers Assistance (DAS) Electronic Control Unit (ECU).
PROC_DAS-GPS-RESET
Resets HEPA filter health score back to 100% - only run this routine after filter replacement.
PROC_VCRIGHT_X_RESET-HEPA-FILTER-HEALTH