Find the procedure. Understand what it does.
Explore diagnostic tests and repair tasks you can run with Tesware on compatible vehicles.
1,357
service tasks
Model 3, Y, S & X
857 tasks Showing 25–48
Clear filtersTests for power, connection, and communication of the battery coolant pump controlled by the Front Vehicle Controller (VCFRONT2).
TEST-SELF_VCFRONT2_X_COOLANT-PUMP-BATTERY
Tests for power, connection, and communication of the battery coolant pump controlled by the Front Vehicle Controller (VCFRONT).
TEST-SELF_VCFRONT_X_COOLANT-PUMP-BATTERY
Backs up Rear Drive Inverter (DIR) application data.
PROC_DIR_X_STORE-DATA-APP
Before replacing the Rear Drive Inverter (DIR), this task backs up the bootloader data.
PROC_PMR_X_STORE-DATA-BOOT
Checks the communication of Bluetooth Low Energy (BLE) endpoints.
TEST-SELF_VCSEC_X_ENDPOINT-COMM
Executes the SERVICE_BLEED routine for both IDB and RCU for 14 cycles. Supplier recommendation is 5x executions (70 total). LEAVE THE CALIPER BLEED NIPPLES CLOSED! Do not press the pedal during execution.
PROC_IDB_RCU_BLEED-INTERNALS
Tests connection and harness of both left and right blind spot indicator lights.
TEST-SELF_VC_X_BLIND-SPOT-LED
Clears open Voltage Sensing Harness (VSH) latch alerts and isolation counters. Resets the High Voltage Processor (HVP) and High Voltage Battery Management System (HVBMS) Electronic Control Units (ECU) in an attempt to clear blocked contactors. Even in the case all internal routines PASS, contactors may still be blocked from closing due to other external conditions.
PROC_HVBMS_X_CLEAR-BLOCKED-CONTACTORS
Runs blower identification first, then runs the HVAC system performance test.
TEST_VC_X_HVAC-BLOWER-IDENTIFICATION-AND-HVAC-PERFORMANCE
Holds the blower stopped, performs high frequency voltage injection, detects blower type, and sets blower type over LIN
PROC_VCLEFT_X_HVAC-BLOWER-IDENTIFICATION
Tests and reports Bluetooth (BT) and Wi-Fi antenna connections.
PING-BASH_BT-WIFI
Runs Bluetooth discovery and returns the IDs of found devices.
TEST-BASH_BT-DISCOVERY
This check succeeds if the gateway reports that the bmp watchog is enabled.
TEST_GTW_BMP-WATCHDOG-ENABLED
Check boot status of the VCFRONT
PROC_VCFRONT_X_BOOT-STATUS
This self test checks the cabin thermistor functionality controlled by the Right Vehicle Controller (VCRIGHT).
TEST-SELF_VCRIGHT_X_HVAC-CABIN-THERMISTORS
Depending on the vehicle type, this routine runs the appropriate calibration routines for profile-managed positions.
PROC_CALIBRATE-DRIVER-SEAT-STEERING-MIRRORS
Calibrate Interior Left Trunk LED
PROC_VCLEFT_REAR-L_CALIBRATE-TRUNK-LED
Calibrate Interior Right Trunk LED
PROC_VCRIGHT_REAR-R_CALIBRATE-TRUNK-LED
The procedure calibrates the left footwell LED light controlled by the Left Vehicle Controller (VCLEFT). During calibration, the light may not illuminate.
PROC_VCLEFT_LEFT_CALIBRATE-FOOTWELL-LED
The procedure calibrates the right footwell LED light controlled by the Right Vehicle Controller (VCRIGHT). During calibration, the light might not illuminate.
PROC_VCRIGHT_RIGHT_CALIBRATE-FOOTWELL-LED
Returns the calibration progress and status for each camera. This task fails if any camera is uncalibrated.
PROC_ICE_X_CAMERA-CALIBRATION-STATUS
Camera Fan Test
PING-HTTP_DAS_X_CAMERA-FAN-SCRIPT
Executes a test to briefly turn on the b-pillar camera heater and verify it draws a minimum amount of current to confirm connectivity
TEST-SELF_VCLEFT_X_CAMERA-HEATER-B-PILLAR
Executes a test to briefly turn on the b-pillar camera heater and verify it draws a minimum amount of current to confirm connectivity
TEST-SELF_VCRIGHT_X_CAMERA-HEATER-B-PILLAR