Vehicle gateway alerts
Browse 237 GTW alert codes and open an entry for its description and recorded conditions.
GTW alert codes
Showing 201–237 of 237
- GTW_w334 — Hrl Folder Space Low GTW_w334_hrlFolderSpaceLow The vehicle Gateway (GTW) detected file system has insufficient disk space for storing continuous and event triggered High Resolution Log (HRL) files.
- GTW_w336 — Possible Can Tx Issue GTW_w336_possibleCanTxIssue An issue has been detected in GTW CAN Tx
- GTW_w350 — M OSD Crc Check GTW_w350_mOSDCrcCheck Unexpected CRC matches/mismatches.
- GTW_w351 — S OSD Crc Check GTW_w351_sOSDCrcCheck Unexpected CRC matches/mismatches.
- GTW_w352 — M ASIL Status Check GTW_w352_mASILStatusCheck Check if any of the bits are set or not
- GTW_w353 — S ASIL Status Check GTW_w353_sASILStatusCheck Check if any of the status bits are set or not
- GTW_w356 — Touch GPIO Status Check GTW_w356_touchGPIOStatusCheck Determine the reason for TCON reset caused by touch/gpio errors
- GTW_w366 — Ui Gear Request Mismatch GTW_w366_uiGearRequestMismatch The Gateway (GTW) detects a gear request from the User Interface that does not match the corresponding gesture processed by the GTW
- GTW_w376 — Bl Failed To Exec Boot Img GTW_w376_blFailedToExecBootImg Bootloader failed to execute boot.img
- GTW_w387 — External Rtc Read Failure GTW_w387_externalRtcReadFailure Gateway time may be invalid. Logs may write to invalid time
- GTW_w388 — Adsp Watchdog Skipped GTW_w388_adspWatchdogSkipped The Gateway (GTW) failed to receive a response to a ping request from the Audio Digital Signal Processor (ADSP). However the GTW successfully received CAN data over Ethernet from the ADSP and so watchdog reset is being skipped.
- GTW_w389 — Rcm Event Detected GTW_w389_rcmEventDetected Gateway has detected a collision event was reported by the RCM (Restraints Control Module)
- GTW_w390 — Display Fw Query Failed GTW_w390_displayFwQueryFailed Indicates that gateway tried to query the disp/disptouch/disposd/dispbridge versions after a panel reset, and failed the read
- GTW_w391 — Adsp Mac Addr Check Failed GTW_w391_adspMacAddrCheckFailed Detected ADSP IP is mapped to a wrong MAC address in GTW's ARP table
- GTW_w393 — Osd Sram Crc Mismatch GTW_w393_osdSramCrcMismatch GTW can not determine if the assets rendered via OSD are accurate.
- GTW_w395 — Lwip Icmp Error GTW_w395_lwipIcmpError lwip stack detects error handling icmp packets
- GTW_w396 — Already In Reverse GTW_w396_alreadyInReverse A request to shift into Reverse is received, but the vehicle is already in Reverse.
- GTW_w397 — Already In Drive GTW_w397_alreadyInDrive A request to shift into Drive is received, but the vehicle is already in Drive.
- GTW_w398 — Awake For Extended Time GTW_w398_awakeForExtendedTime Information purposes only. Alert is set when Gateway has been awake for an extended period of time
- GTW_w399 — Eth If Rx Tcpip Queue Drop GTW_w399_ethIfRxTcpipQueueDrop The vehicle gateway (GTW) dropped received packets on its ethernet interface
- GTW_w400 — Ethl Switch OTP Incorrect GTW_w400_ethlSwitchOTPIncorrect Etherloop switch OTP incorrect
- GTW_w411 — T ASIL Status Check GTW_w411_tASILStatusCheck Check if any of the status bits are set or not
- GTW_w414 — soc Held In Reset GTW_w414_socHeldInReset The vehicle gateway (GTW) is holding the SOC in reset.
- GTW_w420 — Unexpected Can Message Length GTW_w420_unexpectedCanMessageLength The vehicle gateway (GTW) receives a controller area network (CAN) message from another electronic control unit (ECU) with an unexpected length. May be caused by another ECU running a software version incompatible with the version installe…
- GTW_w421 — Modem Eth Link Down GTW_w421_ModemEthLinkDown The gateway detects the Ethernet link to the modem is down.
- GTW_w422 — Eth Switch Severe Congestion Watchdog GTW_w422_ethSwitchSevereCongestionWatchdog The vehicle gateway (GTW) detects severe congestion in the Ethernet switch and initiates a reset.
- GTW_w436 — Possible Can Rx Issue GTW_w436_possibleCanRxIssue The Gateway has identified a possible condition with the Controller Area Network (CAN) driver not receiving messages on a bus.
- GTW_w437 — Soft Flow Control Not Running GTW_w437_softFlowControlNotRunning The vehicle Gateway (GTW) detects that software flow control on the infotainment ethernet switch port is not running.
- GTW_w438 — Wake Source Unknown GTW_w438_wakeSourceUnknown The vehicle Gateway (GTW) has woken from sleep for an unknown reason.
- GTW_w450 — Unexpected Autopilot Control Can Message GTW_w450_unexpectedAutopilotControlCanMessage The vehicle gateway (GTW) receives a Autopilot Control controller area network (CAN) message on an unexpected bus. May be caused by another ECU running a software version incompatible with the version installed on the GTW, a software bug,…
- GTW_w451 — Diag Can Buffer Exhausted GTW_w451_diagCanBufferExhausted All diagCAN frame buffers are in use; new connection was closed.
- GTW_w452 — Diag Can Stale Socket GTW_w452_diagCanStaleSocket diagTaskDoEthWork encountered an fd with no allocated buffer.
- GTW_w453 — Diag Can Fd Set Desync GTW_w453_diagCanFdSetDesync diagEthRxTask timed out waiting for diagTask to return the updated read_fd_set.
- GTW_w454 — Diag Can Frame Overread GTW_w454_diagCanFrameOverread diagTaskDoEthWork read past the current frame boundary in the TCP stream.
- GTW_w455 — Hrl Dump Page Ownership Error GTW_w455_hrlDumpPageOwnershipError During the High-Resolution Logging (HRL) logging process, the HRL dump task writes a page to a file that the HRL state machine is currently filling or hasn't filled yet.
- GTW_w456 — Hrl State Machine Page Ownership Error GTW_w456_hrlStateMachinePageOwnershipError During the High-Resolution Logging (HRL) logging process, the HRL state machine writes data to a page that the HRL dump task is in the process of writing to a file.
- GTW_w463 — Display Edid Read Failed GTW_w463_displayEdidReadFailed Gateway was unable to read cached Extended Display Identification Data (EDID) base or manufacturing data from the center display.