Rear-right drive inverter alerts
Browse 172 DIRER alert codes and open an entry for its description and recorded conditions.
DIRER alert codes
Showing 51–100 of 172
- DIRER_a057 — Ambient UT DIRER_a057_ambientUT Drive Inverter Warning: Ambient under temperature
- DIRER_a058 — Ambient Sensor DIRER_a058_ambientSensor Drive Inverter Warning: Ambient sensor bad
- DIRER_a059 — Heatsink OT DIRER_a059_heatsinkOT Drive Inverter Warning: Heatsink over temperature
- DIRER_a060 — Heatsink UT DIRER_a060_heatsinkUT Drive Inverter Warning: Heatsink under temperature
- DIRER_a061 — Heatsink Sensor DIRER_a061_heatsinkSensor Drive Inverter Warning: Heatsink sensor bad
- DIRER_a062 — System Limp Mode DIRER_a062_systemLimpMode The drive interface (DI) or drive inverter (DIx) electronic control unit (ECU) detects a condition that requires it to trigger system limp mode.
- DIRER_a064 — Torque Intervention DIRER_a064_torqueIntervention The torque production safety monitor has detected excess torque production and inhibited Drive Inverter (DIx) torque production for the remainder of the drive cycle.
- DIRER_a065 — Can Hardware Bus B DIRER_a065_canHardwareBusB
- DIRER_a066 — Can Data Bus B DIRER_a066_canDataBusB The drive interface (DI) or drive inverter (DIx) electronic control unit (ECU) receives a controller area network (CAN) message error on bus B.
- DIRER_a067 — Can Overrun Bus B DIRER_a067_canOverrunBusB There is a controller area network (CAN) overrun error for a given CAN ID (bus B).
- DIRER_a069 — Rotor Temp Limit DIRER_a069_rotorTempLimit The rotor's temperature is too hot, limiting Drive Inverter (DIx) motor torque production.
- DIRER_a070 — Uds Transaction Initiated DIRER_a070_udsTransactionInitiated Diagnostic alert for UDS transaction initiated
- DIRER_a071 — Bus Disconnected DIRER_a071_busDisconnected Drive Inverter Warning: DC bus disconnected
- DIRER_a072 — Gate Drive Fault Counter DIRER_a072_gateDriveFaultCounter The phase gate drive has detected four fault related signals from the induction motor or ten from the magnet motor.
- DIRER_a073 — Motor Speed DIRER_a073_motorSpeed The Drive Unit resolver (motor speed sensor) has detected the motor exceeding typical speed.
- DIRER_a074 — Motor Encoder DIRER_a074_motorEncoder Drive Inverter Warning: Motor encoder error detected in software
- DIRER_a075 — Motor Speed Mismatch DIRER_a075_motorSpeedMismatch The motor speed measured by the Drive Unit resolver does not match the Anti-lock Braking System (ABS) wheel speed sensors.
- DIRER_a076 — Lv Supply OV DIRER_a076_lvSupplyOV The drive interface (DI) or drive inverter (DIx) electronic control unit (ECU) detects a low voltage (LV) battery overvoltage event.
- DIRER_a077 — Lv Supply UV DIRER_a077_lvSupplyUV The drive interface (DI) or drive inverter (DIx) electronic control unit (ECU) detects a low voltage (LV) battery power supply undervoltage event.
- DIRER_a078 — Adc Ref Low DIRER_a078_adcRefLow The drive interface (DI) or drive inverter (DIx) electronic control unit (ECU) detects an analog-to-digital converter (ADC) channel reference below the lower rational bound.
- DIRER_a079 — Adc Ref High DIRER_a079_adcRefHigh The drive interface (DI) or drive inverter (DIx) electronic control unit (ECU) detects an analog-to-digital converter (ADC) channel reference above the upper rational bound.
- DIRER_a084 — Ecc Test Data0 DIRER_a084_eccTestData0 Drive Inverter Warning: ECC error test data alert 1
- DIRER_a086 — Active Discharge On DIRER_a086_activeDischargeOn Drive Inverter Warning: Active discharge is on but bus voltage remains high
- DIRER_a087 — Gtw MIA DIRER_a087_gtwMIA The drive interface (DI) or drive inverter (DIx) electronic control unit (ECU) detects that the gateway (GTW) controller area network (CAN) node is missing (MIA).
- DIRER_a088 — Ui MIA DIRER_a088_uiMIA Drive Inverter Warning: UI (User Interface) node is MIA on CAN for one or multiple messages
- DIRER_a090 — Pm MIA DIRER_a090_pmMIA The drive interface (DI) or drive inverter (DIx) electronic control unit (ECU) detects that the pedal monitor (PM) controller area network (CAN) node is missing (MIA).
- DIRER_a091 — Esp MIA DIRER_a091_espMIA The drive interface (DI) electronic control unit (ECU) detects that the electronic stability program (ESP, also known as traction control) controller area network (CAN) node is missing (MIA).
- DIRER_a092 — Bms MIA DIRER_a092_bmsMIA The drive interface (DI) or drive inverter (DIx) electronic control unit (ECU) detects that the high voltage (HV) battery management system (BMS) controller area network (CAN) node is missing (MIA).
- DIRER_a093 — Can Hardware Bus A DIRER_a093_canHardwareBusA
- DIRER_a094 — Can Data Bus A DIRER_a094_canDataBusA The drive interface (DI) or drive inverter (DIx) electronic control unit (ECU) receives a controller area network (CAN) message error on bus A.
- DIRER_a095 — Can Overrun Bus A DIRER_a095_canOverrunBusA There is a controller area network (CAN) overrun error for a given CAN ID (bus A).
- DIRER_a096 — Memory Error DIRER_a096_memoryError The drive interface (DI) or drive inverter (DIx) electronic control unit (ECU) detects a memory check error.
- DIRER_a097 — Eeprom Error DIRER_a097_eepromError The drive interface (DI) or drive inverter (DIx) electronic control unit (ECU) detects an electrically erasable programmable read-only memory (EEPROM) read/write access error. Check for other alerts that may be set as a result.
- DIRER_a098 — Int Time Too Long DIRER_a098_intTimeTooLong The Drive Inverter (DIx) has detected a DIx thread executing later than expected. The DIx CPU may be diverting resources towards other tasks.
- DIRER_a099 — Thread Overrun DIRER_a099_threadOverrun Drive Inverter Warning: High thread execution time
- DIRER_a100 — Assertion DIRER_a100_assertion Drive Inverter Warning: Firmware assertion
- DIRER_a101 — Ecc Test Data1 DIRER_a101_eccTestData1 Drive Inverter Warning: ECC error test data alert 2
- DIRER_a103 — Low Flow DIRER_a103_lowFlow Drive Inverter Warning: Low flow rate of fluid
- DIRER_a107 — Fpga Error DIRER_a107_fpgaError The Drive Inverter (DIx) has detected an error communicating with the Field Programmable Gate Array (FPGA).
- DIRER_a108 — State Trans DIRER_a108_stateTrans The Drive Unit is not able to transition to Drive state. There may be a condition preventing the Drive Unit from transitioning states.
- DIRER_a110 — Brake MIA DIRER_a110_brakeMIA The drive interface (DI) electronic control unit (ECU) detects that the electronic parking brake (EPB) controller area network (CAN) node is missing (MIA).
- DIRER_a111 — Bad Phase Sensor Calib DIRER_a111_badPhaseSensorCalib The Drive Inverter (DIx) Electrically Erasable Programmable Read-Only Memory (EEPROM) has reported phase sensor calibration is outside valid range.
- DIRER_a112 — No Phase Current DIRER_a112_noPhaseCurrent The Drive Inverter (DIx) Electronic Control Unit (ECU) detects no phase current.
- DIRER_a113 — No Func Heatsink Sensor DIRER_a113_noFuncHeatsinkSensor The three Drive Inverter (DIx) heat sink sensors are not functioning. The DIx heat sink sensors monitor temperature in the motor and fluid port.
- DIRER_a116 — High Speed Wear Counter DIRER_a116_highSpeedWearCounter Drive Inverter Warning: High Speed Wear Counter Exceeded
- DIRER_a117 — Di MIA DIRER_a117_diMIA The Drive Inverter (DIx) node is Missing in Action (MIA) on Controller Area Network (CAN) for one or more messages.
- DIRER_a119 — Hvp MIA DIRER_a119_hvpMIA The drive interface (DI) electronic control unit (ECU) detects that the high voltage processor (HVP) controller area network (CAN) node is missing (MIA).
- DIRER_a120 — Hvlink MIA DIRER_a120_hvlinkMIA Drive Inverter Warning: HVLINK CAN node MIA
- DIRER_a121 — Motor Control Regulation DIRER_a121_motorControlRegulation Drive Inverter Warning: Motor control is out of regulation
- DIRER_a122 — High Stack Usage DIRER_a122_highStackUsage Drive Inverter Warning: High stack usage detected