Front driver door control module alerts

BCFDM alert codes

Showing 51–100 of 123

• BCFDM_a053 — PFDIO Init BCFDM_a053_PFDIOInit
• BCFDM_a054 — PFDIO Process Data BCFDM_a054_PFDIOProcessData
• BCFDM_a055 — PFD Set State BCFDM_a055_PFDSetState
• BCFDM_a056 — Mirror Heat Error BCFDM_a056_MirrorHeatError
• BCFDM_a057 — Reflector Lamp BCFDM_a057_ReflectorLamp
• BCFDM_a058 — Input R High Sync Debug BCFDM_a058_inputRHighSyncDebug Voltage drop on input power is high
• BCFDM_a059 — Input Resistance High BCFDM_a059_inputResistanceHigh A large voltage drop is detected in the input power to the vehicle controller, indicating the resistance on the input power feed to the vehicle controller is higher than expected.
• BCFDM_a060 — Engineering Build BCFDM_a060_engineeringBuild The software installed on the vehicle is intended for engineering use and development purposes only. The vehicle software may have some expected features disabled for testing purposes, or include new features whose function is not yet full…
• BCFDM_a061 — X CP Connected BCFDM_a061_XCPConnected Indicates an active connection to the universal measurement and calibration protocol state machine
• BCFDM_a062 — X CP Was Connected BCFDM_a062_XCPWasConnected Indicates there was an active connection to the universal measurement and calibration protocol state machine
• BCFDM_a063 — Switch Fault BCFDM_a063_SwitchFault A condition affecting switch functionality has been detected.
• BCFDM_a064 — Bus Sleep Req Timeout BCFDM_a064_busSleepReqTimeout Indicates if a bus has timed out of a sleep request from the network manager
• BCFDM_a065 — Ratcheting Detected BCFDM_a065_ratchetingDetected
• BCFDM_a066 — False Latch Cinch BCFDM_a066_falseLatchCinch Not to be confused with a weak cinch. This alert does not imply problems with seal load or door alignment.
• BCFDM_a067 — Missed Short Drop BCFDM_a067_missedShortDrop The body controller will automatically re-issue a short-drop command if a failure to drop is detected.
• BCFDM_a068 — Missed Undrop BCFDM_a068_missedUndrop The body controller will automatically re-issue an undrop command if a failure to undrop is detected.
• BCFDM_a069 — Latch Status Ignored BCFDM_a069_LatchStatusIgnored This alert probably indicates that a firmware bug was encountered. Resetting the front door body controller will temporarily resolve the issue.
• BCFDM_a070 — Latch Failed To Cinch BCFDM_a070_LatchFailedToCinch The door latch cinching actuation completed but the latch is not fully closed.
• BCFDM_a071 — Latch Failed To Release BCFDM_a071_LatchFailedToRelease The door latch release actuation completed but the latch is not OPENED.
• BCFDM_a072 — Unexpect Latch Closed BCFDM_a072_UnexpectLatchClosed The door latch is closed while the door angle is outside the latch closing zone.
• BCFDM_a073 — Unexpect Latch Open BCFDM_a073_UnexpectLatchOpen The door latch transitions to open state unexpectedly.
• BCFDM_a074 — No Latch Entry On Close BCFDM_a074_NoLatchEntryOnClose The front door latch did not detect the striker after the door ramped up to engage the latch.
• BCFDM_a075 — Door Ice Breaker Attempt BCFDM_a075_DoorIceBreakerAttempt The door ice breaker is requested to extend following unsuccessful latch release attempts.
• BCFDM_a076 — Door Ice Breaker Failure BCFDM_a076_DoorIceBreakerFailure The door ice breaker extended but the door latch is not opened.
• BCFDM_a077 — Latch Mech Release Stuck BCFDM_a077_LatchMechReleaseStuck Often caused by a kinked release cable or damaged cable tubing
• BCFDM_a078 — Door Unzeroed BCFDM_a078_DoorUnzeroed The door zero position is cleared.
• BCFDM_a079 — Dvr Side Cfg Mismatch BCFDM_a079_DvrSideCfgMismatch reseting the controller should fix the issue
• BCFDM_a080 — Current Drop Out BCFDM_a080_CurrentDropOut
• BCFDM_a081 — Latch Open In Motion BCFDM_a081_LatchOpenInMotion The door latch transitions to opened state while the vehicle is in motion.
• BCFDM_a082 — Door Zeroed BCFDM_a082_doorZeroed For engineering diagnoses only
• BCFDM_a083 — Unexpected Stop BCFDM_a083_UnexpectedStop The door stopped unexpectedly while opening or closing.
• BCFDM_a084 — Release End Stop BCFDM_a084_ReleaseEndStop
• BCFDM_a085 — ESP Gyro Unstable BCFDM_a085_ESPGyroUnstable
• BCFDM_a086 — Bad ESP Data BCFDM_a086_badESPData
• BCFDM_a087 — Mirr Tilt Test Failure BCFDM_a087_MirrTiltTestFailure This alert exists purely to provide diagnostic information for FW development. Because this alert is triggered only as part of the mirror tilt test routine, it is not expected to occur as part of customer use.
• BCFDM_a088 — V2 Door Brake Cal Pos BCFDM_a088_V2DoorBrakeCalPos This alert exists purely to provide diagnostic information for FW development.
• BCFDM_a089 — V2 Door Brake Cal Neg BCFDM_a089_V2DoorBrakeCalNeg This alert exists purely to provide diagnostic information for FW development.
• BCFDM_a090 — Crash Unlock Error BCFDM_a090_CrashUnlockError
• BCFDM_a091 — Crash State Mismatch BCFDM_a091_CrashStateMismatch
• BCFDM_a092 — Hill Hold BCFDM_a092_HillHold Door applying torque to hold on hill
• BCFDM_a093 — OTP Error BCFDM_a093_OTPError Check OTP region of DFLASH
• BCFDM_a094 — Ice Breaker Retract BCFDM_a094_iceBreakerRetract Debug alert logging icebreaker operational metrics after the icebreaker completed a retracting actuation.
• BCFDM_a105 — ECU Debug Mode BCFDM_a105_ECUDebugMode Production vehicle should not have Debug Jumper in place. Remove jumper from ECU.
• BCFDM_a108 — Latch Release Error BCFDM_a108_LatchReleaseError Check alertLog for more information. If resultingState is CLOSED_BRAKE, the latch's OPEN switch may be disconnected. If previousState is OPENED_BRAKE, the latch's switches and release motor may be all disconnected.
• BCFDM_a109 — Door Brake Uncalibrated BCFDM_a109_DoorBrakeUncalibrated The door motor brake is not calibrated and using default values.
• BCFDM_a110 — PFD Linkage Fault BCFDM_a110_PFDLinkageFault The linkage may have become detached at the ball joint. This alert is only present in factory mode.
• BCFDM_a111 — Latch Release Error BCFDM_a111_LatchReleaseError Check alertLog for more information. If resultingState is CLOSED_BRAKE, the latch's OPEN switch may be disconnected. If previousState is OPENED_BRAKE, the latch's switches and release motor may be all disconnected.
• BCFDM_a112 — Mirror Position BCFDM_a112_MirrorPosition
• BCFDM_a113 — Mirror Memory BCFDM_a113_MirrorMemory
• BCFDM_a114 — Mirror Folding BCFDM_a114_MirrorFolding