Electronic stability program alerts
Browse 319 ESP alert codes and open an entry for its description and recorded conditions.
ESP alert codes
Showing 201–250 of 319
- ESP_a201 — Reverse Gear Stuck Low ESP_a201_reverseGearStuckLow Plausibility failure on reverse gear signal state. Review DI alerts for other failure indicators
- ESP_a202 — Accel Pedal Invalid ESP_a202_accelPedalInvalid Invalid Data Received From Drive Motor Control Module A: Invalid Signal Status
- ESP_a203 — DI torque Timeout ESP_a203_DItorqueTimeout The Electronic Stability Program (ESP) electronic control unit (ECU) is not receiving messages from the drive inverter (DI) on the Party controller area network (CAN) bus within the expected time frame.
- ESP_a204 — DI torque DLC ESP_a204_DItorqueDLC Invalid Data Received From Drive Motor Control Module A: Data Length Code, Checksum or Parity invalid
- ESP_a205 — DI torque Checksum ESP_a205_DItorqueChecksum Invalid Data Received From Drive Motor Control Module A: Data Length Code, Checksum or Parity invalid
- ESP_a206 — DI torque Counter ESP_a206_DItorqueCounter Invalid Data Received From Drive Motor Control Module A: Alive Counter invalid
- ESP_a207 — DI Torque Command Invalid ESP_a207_DITorqueCommandInvalid Invalid Data Received From Drive Motor Control Module A: Invalid Signal Status
- ESP_a208 — DIR PM Invalid ESP_a208_DIRPMInvalid Invalid Data Received From Drive Motor Control Module A: Invalid Signal Status
- ESP_a209 — DI Torque Actual Invalid ESP_a209_DITorqueActualInvalid Invalid Data Received From Drive Motor Control Module A: Invalid Signal Status
- ESP_a210 — DIS torque Timeout ESP_a210_DIStorqueTimeout The Electronic Stability Program (ESP) is not receiving messages from the secondary drive inverter (DIS) on the Party CAN bus within the expected time frame.
- ESP_a211 — DIS torque DLC ESP_a211_DIStorqueDLC Invalid Data Received From Drive Motor Control Module B: Data Length Code, Checksum or Parity invalid
- ESP_a212 — DIS torque Checksum ESP_a212_DIStorqueChecksum Invalid Data Received From Drive Motor Control Module B: Data Length Code, Checksum or Parity invalid
- ESP_a213 — DIS torque Counter ESP_a213_DIStorqueCounter Invalid Data Received From Drive Motor Control Module B: Alive Counter invalid
- ESP_a214 — DIS Torque Command Invalid ESP_a214_DISTorqueCommandInvalid The Electronic Stability Program (ESP) electronic control unit (ECU) receives invalid messages from the secondary drive inverter (DIS) ECU on the Party controller area network (CAN) bus.
- ESP_a215 — DISR PM Invalid ESP_a215_DISRPMInvalid The Electronic Stability Program (ESP) electronic control unit (ECU) receives invalid messages from the secondary drive inverter (DIS) ECU on the Party CAN bus.
- ESP_a216 — DIS Torque Actual Invalid ESP_a216_DISTorqueActualInvalid The Electronic Stability Program (ESP) electronic control unit (ECU) receives invalid messages from the secondary drive inverter (DIS) ECU on the Party controller area network (CAN) bus.
- ESP_a217 — DI vdc Left Timeout ESP_a217_DIvdcLeftTimeout The Electronic Stability Program (ESP) electronic control unit (ECU) is not receiving messages from the drive inverter (DI) ECU on the Party controller area network (CAN) bus within the expected time frame.
- ESP_a218 — DI vdc Left DLC ESP_a218_DIvdcLeftDLC Invalid Data Received From Drive Motor Control Module A: Data Length Code, Checksum or Parity invalid
- ESP_a219 — DI vdc Left Checksum ESP_a219_DIvdcLeftChecksum Invalid Data Received From Drive Motor Control Module A: Data Length Code, Checksum or Parity invalid
- ESP_a220 — DI vdc Left Counter ESP_a220_DIvdcLeftCounter Invalid Data Received From Drive Motor Control Module A: Alive Counter invalid
- ESP_a221 — DI vdc Right Timeout ESP_a221_DIvdcRightTimeout The Electronic Stability Program (ESP) electronic control unit (ECU) is not receiving messages from the drive inverter (DI) ECU on the Party controller area network (CAN) bus within the expected time frame.
- ESP_a222 — DI vdc Right DLC ESP_a222_DIvdcRightDLC Invalid Data Received From Drive Motor Control Module A: Data Length Code, Checksum or Parity invalid
- ESP_a223 — DI vdc Right Checksum ESP_a223_DIvdcRightChecksum Invalid Data Received From Drive Motor Control Module A: Data Length Code, Checksum or Parity invalid
- ESP_a224 — DI vdc Right Counter ESP_a224_DIvdcRightCounter Invalid Data Received From Drive Motor Control Module A: Alive Counter invalid
- ESP_a225 — Config Mismatch ESP_a225_configMismatch The Electronic Stability Program (ESP) receives a message over the controller area network (CAN) from the Gateway (GTW) that the Cyclic Redundancy Check (CRC) value received from the ESP is different than the value expected on GTW.
- ESP_a226 — Bdw Request Invalid ESP_a226_bdwRequestInvalid Invalid BDW Request : BDW is requested within less than 10 seconds since the start of the previous BDW activation.
- ESP_a227 — Bdw Request Active Invalid ESP_a227_bdwRequestActiveInvalid Invalid BDW Request : BDW is requested for more than 10 seconds.
- ESP_a228 — GTW vin Timeout ESP_a228_GTWvinTimeout VIN-Message not received from Gateway
- ESP_a229 — GTW vin DLC ESP_a229_GTWvinDLC Invalid Data Received From Gateway (VIN-Message): Data Length Code, Checksum or Parity invalid
- ESP_a230 — Vin Not Learned ESP_a230_vinNotLearned VIN not programmed
- ESP_a231 — Stored VIN Mismatch ESP_a231_storedVINMismatch VIN: Received VIN does not match stored VIN
- ESP_a232 — PM state2 Timeout ESP_a232_PMstate2Timeout The Electronic Stability Program (ESP) electronic control unit (ECU) is not receiving messages from the pedal monitor (PM) on the Party controller area network (CAN) bus within the expected time frame.
- ESP_a233 — PM state2 Checksum ESP_a233_PMstate2Checksum Invalid Data Received From Pedal Monitor: Data Length Code, Checksum or Parity invalid
- ESP_a234 — PM state2 DLC ESP_a234_PMstate2DLC Invalid Data Received From Pedal Monitor: Data Length Code, Checksum or Parity invalid
- ESP_a235 — PM state2 Counter ESP_a235_PMstate2Counter Invalid Data Received From Pedal Monitor: Alive Counter invalid
- ESP_a236 — Ebr Command State Invalid ESP_a236_ebrCommandStateInvalid Pedal Monitor Intervention: EBR Commands Invalid.
- ESP_a237 — Vdc Command State Invalid ESP_a237_vdcCommandStateInvalid Pedal Monitor Intervention: VDC Commands Invalid
- ESP_a238 — UI odo Timeout ESP_a238_UIodoTimeout The Electronic Stability Program (ESP) electronic control unit (ECU) is not receiving odometer messages from the user interface (UI) within the expected time frame.
- ESP_a239 — UI odo DLC ESP_a239_UIodoDLC UI_odo message integrity check failed
- ESP_a240 — LV Power State Timeout ESP_a240_LVPowerStateTimeout The Electronic Stability Program (ESP) electronic control unit (ECU) is not receiving messages from the front vehicle controller (VCFRONT) on the Party controller area network (CAN) bus within the expected time frame.
- ESP_a241 — LV Power State Checksum ESP_a241_LVPowerStateChecksum ESP CAN - VCFRONT_espLVState message fault
- ESP_a242 — LV Power State DLC ESP_a242_LVPowerStateDLC ESP CAN - VCFRONT_espLVState message fault
- ESP_a243 — LV Power State Counter ESP_a243_LVPowerStateCounter ESP CAN - VCFRONT_espLVState message fault
- ESP_a244 — LV Off State Invalid ESP_a244_LVOffStateInvalid The Electronic Stability Program (ESP) electronic control unit (ECU) receives invalid messages from the front vehicle controller (VCFRONT) on the Party controller area network (CAN) bus.
- ESP_a245 — LV Going Down State Invalid ESP_a245_LVGoingDownStateInvalid The Electronic Stability Program (ESP) electronic control unit (ECU) receives invalid messages from the front vehicle controller (VCFRONT) on the Party controller area network (CAN) bus.
- ESP_a246 — VCRIGHT sensor Timeout ESP_a246_VCRIGHTsensorTimeout The Electronic Stability Program (ESP) electronic control unit (ECU) is not receiving messages from the RIGHT vehicle controller (VCRIGHT) on the Party controller area network (CAN) bus within the expected time frame.
- ESP_a247 — VCRIGHT sensor DLC ESP_a247_VCRIGHTsensorDLC Invalid Data Received From VCRIGHT Control Module: Data Length Code, Checksum or Parity invalid
- ESP_a248 — Vdc Brke Trq Tar Fr L Invalid ESP_a248_vdcBrkeTrqTarFrLInvalid ESP CAN - VDC message state fault
- ESP_a249 — Vdc Brke Trq Tar Fr R Invalid ESP_a249_vdcBrkeTrqTarFrRInvalid ESP CAN - VDC message state fault
- ESP_a250 — Vdc Brke Trq Tar Re L Invalid ESP_a250_vdcBrkeTrqTarReLInvalid ESP CAN - VDC message state fault