Find the procedure. Understand what it does.
Explore diagnostic tests and repair tasks you can run with Tesware on compatible vehicles.
1,357
service tasks
Model 3, Y, S & X
665 tasks Showing 625–648
Clear filtersAttempts to moves the second row seat recliner/backrest rearward, fold the seat, then unfold the seat to the nominal position.
PROC_VC_X_3R-SEAT-RECLINE-FUNCTIONAL-TEST
Resets learned tire estimates to prevent loss of regenerative braking. Clears the tire rotation alert after tire service. Optionally, specify Winter (1) or Summer/All-Season (0) tire type for quicker learning.
PROC_DI_CLEAR-LEARNT-TIRE-OFFSET
Sets the Tire Pressure Monitoring System (TPMS) type configuration to Continental or Tesla BLE.
PROC_TPMS_X_SET-TPMSTYPE-CONFIG
Enable TPMS Factory Autolearn
PROC_VCSEC_X_TPMS-ENABLE-AUTOLEARN
Learns the Vehicle Identification Number (VIN) and sensor ID for Continental TPMS. Values must be read from the sensors using the ATEQ tool.
PROC_TPMS_X_TPMS-LEARN
This test will put the TPMS in learn mode.
PROC_TPMS_X_TPMS-LEARN-MODE
Resets Tire Pressure Monitoring System (TPMS) autonomy health signals after tire service to re-enable robotaxi operations.
PROC_TPMS_X_TPMS-RESET-AUTONOMY
Erases all the Tire Pressure Monitoring System (TPMS) Sensor IDs.
PROC_VCSEC_X_TPMS-ERASE-SENSOR-ID
Learns new Tire Pressure Monitoring System (TPMS) sensor IDs. Enter the TPMS sensor IDs without any special characters.
PROC_TPMS_X_TPMS-SENSOR-LEARN
Learns the new Tire Pressure Monitoring System (TPMS) Sensor IDs.
PROC_VCSEC_X_TPMS-SENSOR-LEARN
The procedure allows the Tire Pressure Monitoring System (TPMS) ECU to learn and locate new sensor unit IDs.
PROC_TPMS_X_TPMS-SENSOR-LEARN-DEPRECATED
Runs all required routines after a Tesla Restraints Control Module (TRCM) replacement and arms the system.
PROC_TRCM_X_SERVICE-TASKS
The procedure triggers an Odin Patch installation if a patch is available for the vehicle's installed firmware signature.
PROC_ICE_X_INSTALL-PATCH
Triggers an Odin Patch uninstall to fall back to installed firmware
PROC_ICE_X_UNINSTALL-PATCH
ODIN checks with the ECU if a log upload is available. If it is, ODIN downloads the data and uploads it to garage logs.
PROC_ODIN_X_TRIGGER-ECU-LOG-UPLOAD
Tune radio by inputting BAND (AM/FM/DAB/XM) and FREQUENCY (station). PLEASE HAVE RADIO PANEL PULLED UP ON THE UI BEFORE RUNNING.
PROC_ICE_X_TUNE-RADIO
Turns off an individual e-fuse power feed for the selected component. The channel powers down respecting the going-down timer. When the timeout expires, power is restored automatically.
PROC_VC_X_POWER-OFF-REQUEST
Turn on the accessory (ACC) power rail.
PROC_CID_X_ACC-RAIL-ON
Turn on the interior cabin map lights.
PROC_ICE_X_MAP-LIGHTS-ON
This routine will update the Gateway pack config to match what the BMS is reporting.
PROC_CID_X_WRITE-GTW-PACK-CONFIG
Requests an upload of the logged CAN data between the specified start and end time.
PROC_ICE_X_LOGS-UPLOADER
Used to set the max brightness parameter stored in the RGB ECU
PROC_VCLEFT_SET-RGB-ATTENUATION
Sets the ride height sensor offsets for VCLEFT to FRONT_AXLE_HEIGHT and REAR_AXLE_HEIGHT. Default value is 155.
PROC_VCLEFT_X_SET-HEIGHT-SENSOR-OFFSETS
Used to set the max brightness parameter stored in the RGB ECU
PROC_VCRIGHT_SET-RGB-ATTENUATION