Skip to content

Tesla service tasks.

Find the procedure. Understand what it does. Explore diagnostic tests and repair tasks you can run with Tesware on compatible vehicles.

1,357

service tasks

Model 3, Y, S & X

Find a service task

665 tasks Showing 337–360

Clear filters
Service procedures

Louver Calibration

Performs the louver calibration routine.

PROC_VCFRONT_X_LOUVER-CALIBRATION

Model 3 / Y Model S / X (2021+)
Service procedures

Louver Calibration

Runs the ModelS front louver calibration after actuator replacement. And returns the calibration status of all four louvers.

PROC_THC_X_LOUVER-CALIBRATION

Model S / X (legacy)
Service procedures

LR Door Handle Calibration

Calibrate Left Rear door handle by actuating the fork to its maximum and minimum positions. Also configure the door handle controller to make it learn its location, if needed.

PROC_VCLEFT_REAR-L_CALIBRATE-DOOR-HANDLE

Model S / X (2021+)
Service procedures

LVBMS Reconnect LV Battery

Reconnects the Low Voltage Battery MOSFET on Model S and X platforms.

PROC_VCBATT_X_RECONNECT-LV-BATTERY

Model S / X (2021+)
Service procedures

LVBMS Reconnect LV Battery

Reconnects the Low Voltage Battery MOSFET on Model 3 and Y platforms.

PROC_VCBATT1_X_RECONNECT-LV-BATTERY

Model 3 / Y
Service procedures

LVBMS Reconnect LV Battery

Reconnects the Low Voltage (LV) Battery's MOSFET.

PROC_VCFRONT_X_RECONNECT-LV-BATTERY

Model 3 / Y
Service procedures

Manage Screenshots

Optionally lists / deletes all screenshots, or downloads / deletes a specified screenshot from car's file system

PROC_CID_X_MANAGE-SCREENSHOTS

Model 3 / Y Model S / X (legacy) Model S / X (2021+)
Service procedures

Measure EAS Air Mass (CONTI)

Measure the CONTI Air Suspension air mass. Will return one of AIR_MASS_TOO_LOW, AIR_MASS_OK, or AIR_MASS_TOO_HIGH.

PROC_EAS_X_MEASURE-AIR-MASS

Model S / X (legacy)
Service procedures

Model S Door Handle Configuration Reset - Front Driver - Gen 2.1/3.0

Reset front driver door handle controller configuration to undefined value. This will allow an already configured door handle controller to be installed and calibrated on any door. Make sure to run the appropriate door handle calibration routine afterward.

PROC_DHFD_FRONT-DRV_DOOR-HANDLE-RESET

Model S / X (legacy)
Service procedures

Model S Door Handle Configuration Reset - Front Passenger - Gen 2.1/3.0

Reset front passenger door handle controller configuration to undefined value. This will allow an already configured door handle controller to be installed and calibrated on any door. Make sure to run the appropriate door handle calibration routine afterward.

PROC_DHFP_FRONT-PAS_DOOR-HANDLE-RESET

Model S / X (legacy)
Service procedures

Model S Door Handle Configuration Reset - Rear Driver - Gen 2.1/3.0

Reset rear driver door handle controller configuration to undefined value. This will allow an already configured door handle controller to be installed and calibrated on any door. Make sure to run the appropriate door handle calibration routine afterward.

PROC_DHRD_REAR-DRV_DOOR-HANDLE-RESET

Model S / X (legacy)
Service procedures

Model S Door Handle Configuration Reset - Rear Passenger - Gen 2.1/3.0

Reset rear passenger door handle controller configuration to undefined value. This will allow an already configured door handle controller to be installed and calibrated on any door. Make sure to run the appropriate door handle calibration routine afterward.

PROC_DHRP_REAR-PAS_DOOR-HANDLE-RESET

Model S / X (legacy)
Service procedures

Model X 2nd Row Center Seat Install Mode OFF

Disable 2nd row center seat install mode, which enables pitch movement, track motor speed limit and endstop positions.

PROC_BCS2C_R2-C_SEAT-INSTALL-MODE-OFF

Model S / X (legacy)
Service procedures

Model X 2nd Row Center Seat Install Mode ON

Enable 2nd row center seat install mode, which disables pitch movement, track motor speed limit and endstop positions.

PROC_BCS2C_R2-C_SEAT-INSTALL-MODE-ON

Model S / X (legacy)
Service procedures

Model X 2nd Row Left Seat Install Mode OFF

Disable 2nd row left seat install mode, which enables pitch movement, track motor speed limit and endstop positions.

PROC_BCS2L_R2-L_SEAT-INSTALL-MODE-OFF

Model S / X (legacy)
Service procedures

Model X 2nd Row Left Seat Install Mode ON

Enable 2nd row left seat install mode, which disables pitch movement, track motor speed limit and endstop positions.

PROC_BCS2L_R2-L_SEAT-INSTALL-MODE-ON

Model S / X (legacy)
Service procedures

Model X 2nd Row Right Seat Install Mode OFF

Disable 2nd row right seat install mode, which enables pitch movement, track motor speed limit and endstop positions.

PROC_BCS2R_R2-R_SEAT-INSTALL-MODE-OFF

Model S / X (legacy)
Service procedures

Model X 2nd Row Right Seat Install Mode ON

Enable 2nd row right seat install mode, which disables pitch movement, track motor speed limit and endstop positions.

PROC_BCS2R_R2-R_SEAT-INSTALL-MODE-ON

Model S / X (legacy)
Service procedures

Model X Active Spoiler Calibration

This routine will trigger the automatic spoiler calibration routine in the BCREAR module. The calibration will tell the BCREAR where the spoiler endstops are and will calibrate the spoiler anti-pinch.

PROC_BCREAR_REAR_TEST-SPOILER

Model S / X (legacy)