Find the procedure. Understand what it does.
Explore diagnostic tests and repair tasks you can run with Tesware on compatible vehicles.
1,357
service tasks
Model 3, Y, S & X
676 tasks Showing 553–576
Clear filtersThis routine writes the correct High Voltage Interlock Loop (HVIL) type of the vehicle to the High Voltage Controller (HVC).
PROC_HVP_X_HVIL-SET-CONFIGURATION
Sets modem on / off / cycle. 'on' state be restored by qtcar-connman if it is currently running.
PROC_ICE_X_SET-MODEM-ONLY-POWER-STATE
Sets modem power state and stops / starts related cell processes. Power_state can be 'on', 'off', or 'cycle'.
PROC_ICE_X_SET-MODEM-POWER-STATE
The procedure generates a random four digit Valet Mode PIN and optionally enables Valet Mode on a delivered vehicle.
PROC_ICE_X_SET-VALET-MODE-UNDELIVERED
The test displays all public keys on the whitelist of the Security Controller (VCSEC) and optionally shows permissions.
TEST_VCSEC_X_DISPLAY-KEY-WHITELIST
Tests for power, connection, and communication of the shut-off valve controlled by the Front Vehicle Controller (VCFRONT).
TEST-SELF_VCFRONT_X_SOLENOID
Enables or disables the onboard embedded SIM. When the embedded SIM is disabled, the external SIM card is used. The procedure may take a few minutes to complete. To maintain connectivity, make sure a physical SIM card is present in the external slot when disabling the onboard SIM.
PROC_ICE_X_ENABLE-DISABLE-SIM-CARD
Checks the State of Charge (SOC) on the vehicle.
PROC_CID_X_DV-CHARGE-PERCENT-CHECK-NA
Resets all HV battery brick State of Charge (SOC) values based on the latest Open Circuit Voltage (OCV) brick measurements. During normal operation, the HVBMS ECU calculates brick SOCs from multiple data sources. This routine should be executed when the SOC is >90% or <15% and the HV battery has rested (not charging, driving, or climate ON) for at least one hour within that SOC range.
PROC_HVBMS_X_RESET-SOC
Soft-fuse or un-soft-fuse infotainment
PROC_ICE_X_SOFT-FUSE
Resets the HV battery State of Health (SOH) state, enabling a new SOH test to be performed if previously inhibited.
PROC_HVX_X_RESET-SOH
Overrides the drive unit speed and torque limits set by Factory or Service Mode.
PROC_ICE_X_ENTER-LIMIT-OVERRIDE
Starts the Close Refrigerant Valves routine and returns. The routine will run for up to 5 hours, but the final results are not reported
PROC_VCFRONT_X_START-CLOSE-REFRIGERANT-VALVES
Activates Service Mode on the left Electronic Park Break (EPBL).
PROC_EPBL_START-SERVICE-MODE
Activates Service Mode on the right Electronic Park Break (EPBR).
PROC_EPBR_START-SERVICE-MODE
Starts discharging the High Voltage (HV) battery by producing waste heat in the Drive Units and rejecting that heat out the radiator. Automatically stops when the HV Battery State of Charge (SOC) max reaches the user-selected target SOC.
PROC_VCFRONT_X_HV-DISCHARGE-START
Starts the Thermal Fluid Fill and Thermal Fluid Drain procedures. Runs for up to 5 hours, monitoring status.
PROC_VCFRONT_X_START-THERMAL-FILL-DRAIN
Starts the Thermal Fill Drain for coolant only and returns. The routine will run for up to 50 minutes, but the final results are not reported
PROC_VCFRONT_X_START-THERMAL-FILL-DRAIN-COOLANT
Starts the Thermal Fill Drain for refrigerant only and returns. The routine will run for up to 50 minutes, but the final results are not reported
PROC_VCFRONT_X_START-THERMAL-FILL-DRAIN-REFRIGERANT
Checks the State of Charge (SoC) on the vehicle.
PROC_CID_X_DV-CHARGE-PERCENT-CHECK-ROW
This routine checks if the wheel alignment has been disturbed after a suspension repair. Drive the vehicle on a straight road above 30kph/18mph. If the alignment has changed, the routine will indicate that a wheel alignment is required.
TEST-SELF_EPAS_X_STEERING-CENTER-OFFSET-SERVICE
Calibrates the steering column. Sets the zero position of each axis. Determines the number of motor encoder counts it takes to reach the other endpoint of the column's travel.
PROC_STEERING_COLUMN_CALIBRATION
Tests up/down and in/out movement of the steering column by moving the steering column a short distance in each direction.
PROC-VCLEFT_X_STEERING-COLUMN-CALIBRATION
Tests up/down and in/out movement of the steering column by shortly moving the steering column in each direction.
TEST-SELF_VCLEFT_X_STEERING-COLUMN