Displays information about connected chargers and if they are configured as Master or Slave.
Designed to be used together with PROC_CHG_X_CHARGER-CONFIG-SET-MASTER and PROC_CHG_X_CHARGER-CONFIG-SET-SLAVE to configure new or replaced chargers.
When working on the chargers connect the car to 12V support.
Disconnecting the chargers will run power off the 12V battery and the car will become unresponsive quickly.
Only one charger can be connected at a time for the configuration.
Before reading status or performing any configuration;
--Enter service mode and perform GTW unlock procedure.
If adding a second charger ;
--Set the current charger as Slave and disconnect it.
--Connect the new charger and configure it as Master
--Connect both chargers and make sure they are being detected
--Run Status script again to read Out the 'Charger types'. Write Charger type to GTW using the infotainment dashboard in Tbx3.
If replacing a single charger ;
--Connect new charger in place of old one.
--New charger should be set as Master, no configuration needed.
--Run Status script to read Out the 'Charger type'. Write Charger type to GTW using the infotainment dashboard in Tbx3.
Important Note !
--In a dual charger configuration, the charger behind the driver seat has to be set as Slave and the Master is positioned behind the passenger.
--New charger are by default configured as Master
PROC_CHG_X_CHARGER-STATUS
Model S / X (legacy)
Create a report of vehicle states such as UI Mode, BMS State, Timezone, and more.
This is useful for verifying vehicle state before performing a remote repair.
TEST-BASH_ICE_X_CAR-STATUS
Model S / X (legacy)
This test ensures several important processes are running on the CID.
TEST-BASH_CID_X_CHECK-PROCESS
Model S / X (legacy)
Check ride height calibration of the Continental air suspension. Please input the ride height measured at each corner of the vehicle.
PROC_EAS_X_CHECK-RIDE-HEIGHT-CALIBRATION
Model S / X (legacy)
The check databases test checks pragma integrity for all databases and searches for errors.
TEST-BASH_ICE_X_CHECK-DATABASES
Model 3 / Y
Model S / X (legacy)
Model S / X (2021+)
Computes a hash for a given file to verify file integrity. Can be used for validating newly created navigation maps, images, or system files.
TEST-BASH_ICE_X_CHECK-HASH
Model S / X (legacy)
Analyze mounted devices, logical volumes, and disk usage.
TEST-BASH_ICE_X_CHECK-SYSTEM
Model 3 / Y
Model S / X (legacy)
Model S / X (2021+)
Returns the signature of an available odin patch on firmware server if one is released
TEST_ICE_X_ODIN-PATCH-AVAILABLE
Model 3 / Y
Model S / X (legacy)
Model S / X (2021+)
Check the electrical connection between the MCU and the Pedestrian Warning Speaker
TEST-BASH_SPK_X_PWS-CHECK
Model S / X (legacy)
Check the electrical connection between the MCU and all the speakers that are connected directly to the MCU
TEST-BASH_SPK_X_MCU-CHECK
Model S / X (legacy)
Read the /home filesystem superblock to display information like available
inodes and memory blocks. This will provide insight into filesystem-related issues
such as insufficient inodes or disk space. The most helpful result is the 'Free Inodes'
line which should show a number over 10,000.
TEST-BASH_ICE_X_READ-HOME-PARAMS
Model 3 / Y
Model S / X (legacy)
Model S / X (2021+)
Checks whether the left turn signal indicator light is on and functioning as expected. This routine monitors CAN to confirm whether the indicator light is turned on.
PROC_VCFRONT_L_SIGNAL-LIGHT-LEFT
Model S / X (legacy)
The procedure checks status of a runsv process running on the car computer.
PROC_ICE_X_ICE-PROC-STATUS
Model 3 / Y
Model S / X (legacy)
Model S / X (2021+)
Checks whether the right turn signal indicator light is on and functioning as expected. This routine monitors CAN to confirm whether the indicator light is turned on.
PROC_VCFRONT_R_SIGNAL-LIGHT-RIGHT
Model S / X (legacy)
Check Tesla Air Suspension (TAS) Electronic Control Unit (ECU) mode.
PROC_TAS_X_CHECK-RUN-MODE
Model 3 / Y
Model S / X (legacy)
Model S / X (2021+)
The test reads the /var filesystem superblock to display information like available
inodes and memory blocks. The most helpful result is the 'Free Inodes' line which should show a number over 10,000.
TEST-BASH_ICE_X_READ-VAR-PARAMS
Model 3 / Y
Model S / X (legacy)
Model S / X (2021+)
Tests communication with the Supercharger (CHGPH1) Electronic Control Unit (ECU). Communication is established via Unified Diagnostics Services (UDS) over the Controller Area Network (CAN).
PING-TP_CHGPH1
Model S / X (legacy)
Tests communication with the Supercharger (CHGPH2) Electronic Control Unit (ECU). Communication is established via Unified Diagnostics Services (UDS) over the Controller Area Network (CAN).
PING-TP_CHGPH2
Model S / X (legacy)
Tests communication with the Supercharger (CHGPH3) Electronic Control Unit (ECU). Communication is established via Unified Diagnostics Services (UDS) over the Controller Area Network (CAN).
PING-TP_CHGPH3
Model S / X (legacy)
Tests communication with the CHGVI Electronic Control Unit (ECU). Communication is established via Unified Diagnostics Services (UDS) over the Controller Area Network (CAN).
PING-TP_CHGVI
Model S / X (legacy)
This is an automated test to ensure the lower cladding modules in the falcon wing door are plugged in and reading valid data from the capacitive sensing circuits. This test must be run while the door is stationary and ran at least 5 seconds after the door has stopped moving. The test will not validate whether the sensors will properly detect objects or not.
PROC_BCFALCD_FALCON-DRV_CLADDING-AUTOMATED-FALCD
Model S / X (legacy)
This is an automated test to ensure the lower cladding modules in the falcon wing door are plugged in and reading valid data from the capacitive sensing circuits. This test must be run while the door is stationary and ran at least 5 seconds after the door has stopped moving. The test will not validate whether the sensors will properly detect objects or not.
PROC_BCFALCP_FALCON-PASS_CLADDING-AUTOMATED-FALCP
Model S / X (legacy)
This routine will clear the BMS brick substitution bit and return
the BMS to normal operation.
This routine shall ONLY be executed after installing
a new/remanufactured HV battery or on rare occasion when instructed to do so by
engineering. See Toolbox Article 550300 for more information.
PROC_BMS_X_CLEAR-BRICK6-SUBSTITUTION
Model S / X (legacy)
This routine clears the open voltage sense harness (VSH) alerts BMS_f/w107_SW_Cell_Voltage_Sensor
and BMS_f/w177_OpenVshDetected latch bit within the BMS NVRAM.
This routine shall ONLY be executed after installing a new/remanufactured HV battery or on
rare occasion when instructed to do so by engineering.
PROC_BMS_X_CLEAR-LATCH-BITS
Model S / X (legacy)