Top-Right Steering Wheel Button
This check is designed to monitor for a CAN signal change whenever the top-right steering wheel button is pressed. Test will pass when a button press is detected.
TEST_SCCM_X_SCCM-2014-TOP-RIGHT
Find the procedure. Understand what it does.
Explore diagnostic tests and repair tasks you can run with Tesware on compatible vehicles.
1,357
service tasks
Model 3, Y, S & X
421 tasks Showing 385–408
Clear filtersThis check is designed to monitor for a CAN signal change whenever the top-right steering wheel button is pressed. Test will pass when a button press is detected.
TEST_SCCM_X_SCCM-2014-TOP-RIGHT
Tests communication with the Tire Pressure Monitoring System (TPMS) Electronic Control Unit (ECU). Communication is established via Unified Diagnostics Services (UDS) over the Controller Area Network (CAN).
PING-TP_TPMS
Learns the Vehicle Identification Number (VIN) and sensor ID for Continental TPMS. Values must be read from the sensors using the ATEQ tool.
PROC_TPMS_X_TPMS-LEARN
This test will put the TPMS in learn mode.
PROC_TPMS_X_TPMS-LEARN-MODE
Learns new Tire Pressure Monitoring System (TPMS) sensor IDs. Enter the TPMS sensor IDs without any special characters.
PROC_TPMS_X_TPMS-SENSOR-LEARN
The procedure triggers an Odin Patch installation if a patch is available for the vehicle's installed firmware signature.
PROC_ICE_X_INSTALL-PATCH
Triggers an Odin Patch uninstall to fall back to installed firmware
PROC_ICE_X_UNINSTALL-PATCH
ODIN checks with the ECU if a log upload is available. If it is, ODIN downloads the data and uploads it to garage logs.
PROC_ODIN_X_TRIGGER-ECU-LOG-UPLOAD
Tune radio by inputting BAND (AM/FM/DAB/XM) and FREQUENCY (station). PLEASE HAVE RADIO PANEL PULLED UP ON THE UI BEFORE RUNNING.
PROC_ICE_X_TUNE-RADIO
Perform a tuner and antenna connection check.
TEST-BASH_CID_X_TUNER-ANTENNA
Based on vehicle configuration, corresponding option of tuner is checked.
TEST-BASH_CID_X_TUNER-ANTENNA-ALL
This checks the connections of tuner and antenna.
TEST-BASH_CID_X_TUNER-ANTENNA-APAC-BASE
This checks the connections of tuner and antenna.
TEST-BASH_CID_X_TUNER-ANTENNA-APAC-PREMIUM
This checks the connections of tuner and antenna.
TEST-BASH_CID_X_TUNER-ANTENNA-EU
This checks the connections of tuner and antenna.
TEST-BASH_CID_X_TUNER-ANTENNA-NA-BASE
This checks the connections of tuner and antenna.
TEST-BASH_CID_X_TUNER-ANTENNA-NA-PREMIUM
This checks the connections of tuner and antenna.
TEST-BASH_CID_X_TUNER-ANTENNA-ROW
Turn on the accessory (ACC) power rail.
PROC_CID_X_ACC-RAIL-ON
Turn on the interior cabin map lights.
PROC_ICE_X_MAP-LIGHTS-ON
Tests the connectivity and signal strength of the Ultra High Frequency (UHF) charge port antenna on the Model X located in the grid of the rear liftgate glass. The antenna will detect a signal from a standard UHF transmitter, but the transmitter is not sending a request to Open the charge port door, so the charge port is not required to respond by opening.
TEST_BCCEN_X_UHF-CHARGE-PORT
This routine will update the Gateway pack config to match what the BMS is reporting.
PROC_CID_X_WRITE-GTW-PACK-CONFIG
Before running this routine, ensure the target updater is awake. Checks the status directly on an updater. This returns firmware package data including signatures, fail counts, fuse state, and more.
TEST-BASH_ICE_X_UPDATER-STATUS
Perform USB check.
TEST-BASH_CID_X_USB
Lists the files on a plugged-in USB device. While the display is off, external devices may not be mounted.
TEST-BASH_ICE_X_LSUSB