Find the procedure. Understand what it does.
Explore diagnostic tests and repair tasks you can run with Tesware on compatible vehicles.
1,357
service tasks
Model 3, Y, S & X
421 tasks Showing 313–336
Clear filtersThe procedure resets ride height calibration values to default.
PROC_TAS_X_RESET-RIDE-HEIGHT-CALIBRATION
This routine resets the HV battery state of charge (SOC) according to the current open circuit voltage (OCV) brick measurements. During normal operation, the BMS derives the estimated SOC from multiple data sources. In the event of a large accumulated error, this routine can reset the calculated SOC based solely on the open circuit brick voltages. Important: - Pack contactors are required to be opened prior to this routine being executed. - This routine should ONLY be executed when the SOC is >90% or <15% and the HV battery has rested (not charging, driving or climate ON) for at least one hour within that SOC range.
PROC_BMS_X_RESET-SOC
The procedure resets the PIN for Speed Limit Mode to '0000'.
PROC_ICE_X_RESET-SPEEDLIMIT-PIN
The procedure restores user profile data from an encrypted backup on mothership.
PROC_ICE_X_PROFILE-RESTORE
Records configurations such as serial numbers of components in the Bosch restraint system. and check RCM for errors. If no diagnostic trouble codes (DTCs) are present, the test will arm the airbag system.
PROC_RCM_X_SERVICE-TASKS
This tests the functionality of the Right Front Door Speaker (Base).
TEST-BASH_CID_FRONT-R_SPEAKER-RFDO-BASE
This tests the functionality of the Right Front Door Speaker (Premium).
TEST-BASH_CID_FRONT-R_SPEAKER-RFDO
This tests the functionality of the Right Front Tweeter Speaker (Base).
TEST-BASH_CID_FRONT-R_SPEAKER-RFTW-BASE
This tests the functionality of the Right Front Tweeter Speaker (Premium).
TEST-BASH_CID_FRONT-R_SPEAKER-RFTW
This tests the functionality of the Right Rear Door Speaker (Base).
TEST-BASH_CID_REAR-R_SPEAKER-RRDO-BASE
This tests the functionality of the Right Rear Door Speaker (Premium).
TEST-BASH_CID_REAR-R_SPEAKER-RRDO
This tests the functionality of the Right Rear Lift Gate Speaker (Premium).
TEST-BASH_CID_REAR-R_SPEAKER-RRLG
Check that the right signal light is working correctly.
TEST_VCFRONT_R_SIGNAL-LIGHT
The this routine will trigger the automatic spoiler calibration routine in the BCREAR module. The calibration will tell the BCREAR where the spoiler endstops are and will calibrate the spoiler's anti-pinch feature.
PROC_BCREAR_X_SPOILER
Performs a lsusb command on the Center Information Display (CID). Tests connection of devices connected to USB, such as the touchscreen, cellular modem, and Bluetooth.
TEST_ICE_X_LSUSB
Test Controller Area Network (CAN) communication with the Steering Column Control Module (SCCM).
PING-TP_SCCM
Searches the SX gateway logs for a byte range and a file range given start and end timestamps in s.
PROC_MCU_X_SEARCH-GATEWAY-LOGS
The procedure checks recent syslogs for all User Interface (UI) alerts. Some alerts are benign, such as seatbelt reminders, but others may represent service concerns. This Task will find all UI alerts along with when each occurred. Note that these timestamps are always PDT.
TEST-BASH_ICE_X_SEARCH-UI-ALERTS
Tests communication with the SEC Electronic Control Unit (ECU). Communication is established via Unified Diagnostics Services (UDS) over the Controller Area Network (CAN).
PING-TP_SEC
Checks the state of the nearest keyfob, then tries to update it if it is 80-bit encryption or unlocked
PROC_SEC_X_PEKTRON-KEY-UPDATE
This routine performs the VIN Learn, and side configuration learn for Pektron door module. This is necessary to ensure the security controller (SEC) recognizes the correct vehicle configuration. Test will always report as passed to MES due to unreliability of the routine. Routine is necessary after any configuration changes that affect the SEC module.
PROC_SEC_X_PEKTRON-VIN-LEARN
Clears remote service alerts.
PROC_ICE_X_CLEAR-SERVICE-ALERT
Before running this routine, ensure the parking brake is engaged. Do not use this routine after a car computer replacement. Performs fast redeployment of the currently installed firmware version to all Controller Area Network (CAN) Electronic Control Units (ECU). This routine uses specific logic to reinstall directly from the online bank, avoiding the need for signature verification and staging.
UPDATE_CAN-REDEPLOY
Deletes all user settings and data from /home. Ensure that user profiles are backed up before running this procedure to prevent permanently erasing user data.
PROC_ICE_X_SERVICE-FACTORY-RESET