Find the procedure. Understand what it does.
Explore diagnostic tests and repair tasks you can run with Tesware on compatible vehicles.
1,357
service tasks
Model 3, Y, S & X
857 tasks Showing 721–744
Clear filtersStarts discharging the High Voltage (HV) battery by producing waste heat in the Drive Units and rejecting that heat out the radiator. Automatically stops when the HV Battery State of Charge (SOC) max reaches the user-selected target SOC.
PROC_VCFRONT2_X_HV-DISCHARGE-START
Starts discharging the High Voltage (HV) battery by producing waste heat in the Drive Units and rejecting that heat out the radiator. Automatically stops when the HV Battery State of Charge (SOC) max reaches the user-selected target SOC.
PROC_VCFRONT_X_HV-DISCHARGE-START
Starts the Thermal Fluid Fill and Thermal Fluid Drain procedures. Runs for up to 5 hours, monitoring status.
PROC_VCFRONT_X_START-THERMAL-FILL-DRAIN
Starts the Thermal Fluid Fill and Thermal Fluid Drain procedures and runs for up to 5 hours, monitoring status.
PROC_VCFRONT2_X_START-THERMAL-FILL-DRAIN
Starts the Thermal Fill Drain for coolant only and returns. The routine will run for up to 50 minutes, but the final results are not reported
PROC_VCFRONT_X_START-THERMAL-FILL-DRAIN-COOLANT
Starts the Thermal Fill Drain for refrigerant only and returns. The routine will run for up to 50 minutes, but the final results are not reported
PROC_VCFRONT2_X_START-THERMAL-FILL-DRAIN-REFRIGERANT
Starts the Thermal Fill Drain for refrigerant only and returns. The routine will run for up to 50 minutes, but the final results are not reported
PROC_VCFRONT_X_START-THERMAL-FILL-DRAIN-REFRIGERANT
Checks the State of Charge (SoC) on the vehicle.
PROC_CID_X_DV-CHARGE-PERCENT-CHECK-ROW
This routine checks if the wheel alignment has been disturbed after a suspension repair. Drive the vehicle on a straight road above 30kph/18mph. If the alignment has changed, the routine will indicate that a wheel alignment is required.
TEST-SELF_EPAS_X_STEERING-CENTER-OFFSET-SERVICE
Calibrates the steering column. Sets the zero position of each axis. Determines the number of motor encoder counts it takes to reach the other endpoint of the column's travel.
PROC_STEERING_COLUMN_CALIBRATION
Tests up/down and in/out movement of the steering column by moving the steering column a short distance in each direction.
PROC-VCLEFT_X_STEERING-COLUMN-CALIBRATION
Tests up/down and in/out movement of the steering column by shortly moving the steering column in each direction.
TEST-SELF_VCLEFT_X_STEERING-COLUMN
The self-test checks the Steering Wheel Controller (SWC) ECU communication with the Left Vehicle Controller (VCLEFT) ECU on the Local Interconnect Network (LIN) bus network.
TEST-SELF_VCLEFT_X_SWC
Model 3 Non-heat-pump ONLY - Stops coolant valve flow test
TEST-SELF_VCFRONT_X_THERMAL-COOLANT-VALVE-FLOW-STOP
Stops the High Voltage (HV) Battery discharge routine, if active.
PROC_VCFRONT2_X_HV-DISCHARGE-STOP
Stops the High Voltage (HV) Battery discharge routine, if active.
PROC_VCFRONT_X_HV-DISCHARGE-STOP
The procedure stops the Close Refrigerant Valves routine and returns results.
PROC_VCFRONT2_X_STOP-CLOSE-REFRIGERANT-VALVES
The procedure stops the Close Refrigerant Valves routine and returns results.
PROC_VCFRONT_X_STOP-CLOSE-REFRIGERANT-VALVES
The procedure stops the Thermal Coolant Flow Cycle with all coolant modes.
PROC_VCFRONT2_X_STOP-THERMAL-COOLANT-FLOW-CYCLE
The procedure stops the Thermal Coolant Flow Cycle with all coolant modes.
PROC_VCFRONT_X_STOP-THERMAL-COOLANT-FLOW-CYCLE
Stops the Thermal Fluid Fill and Thermal Fluid Drain routine, allowing the coolant valve, coolant pumps, and Electronic Expansion Valves (EXVs) to return to their default operational states.
PROC_VCFRONT2_X_STOP-THERMAL-FILL-DRAIN
Stops the Thermal Fill and Drain routine and allows the coolant valve, coolant pumps, and Electronic Expansion Valves (EXVs) to return to their default operational states.
PROC_VCFRONT_X_STOP-THERMAL-FILL-DRAIN
Store drive INVERTER bootloader and application data before replacement
PROC_PMX_X_STORE-ALL-DATA-AWD
Store drive INVERTER bootloader and application data before replacement
PROC_PMX_X_STORE-ALL-DATA-AWD-OR-AWD-DUAL-REAR