Prepare for Supercharge - Start
Starts pre-heating the High Voltage (HV) battery based on the Supercharger type selected.
PROC_HVBMS_X_PREPARE-FOR-SUPERCHARGE-START
Find the procedure. Understand what it does.
Explore diagnostic tests and repair tasks you can run with Tesware on compatible vehicles.
1,357
service tasks
Model 3, Y, S & X
857 tasks Showing 505–528
Clear filtersStarts pre-heating the High Voltage (HV) battery based on the Supercharger type selected.
PROC_HVBMS_X_PREPARE-FOR-SUPERCHARGE-START
Stops the Prepare for Supercharge High Voltage Battery Management System (HVBMS) routine.
PROC_HVBMS_X_PREPARE-FOR-SUPERCHARGE-STOP
Tests communication with the Cabin Heater (PTC) Electronic Control Unit (ECU). Communication is established via Unified Diagnostics Services (UDS) over the Controller Area Network (CAN).
PING-TP_PTC
Checks for inoperative Positive Temperature Coefficient (PTC) heater rods and stores the result in the Right Vehicle Controller (VCRIGHT) ECU. Allows the VCRIGHT to restore operation of the PTC heater by not turning on the inoperative rod. To clear the stored information in VCRIGHT, run this routine if the PTC heater is replaced.
TEST-SELF_VCRIGHT_X_PTC-COMPROMISED-ROD-DETECTION
Resets the Positive Temperature Coefficient (PTC) Electronic Control Unit (ECU). Reset is executed via Unified Diagnostics Services (UDS) over the Controller Area Network (CAN).
TEST-RESET_PTC
Tests the electrical connection between the car computer and the Pedestrian Warning System (PWS).
TEST-BASH_SPK_X_PWS-CHECK
Tests the functionality of the radar heater connected to the front vehicle controller (VCFRONT) ECU.
TEST-SELF_VCFRONT_X_RADAR-HEATER
Resets the Forward Facing Radar (RADC) Electronic Control Unit (ECU). Reset is executed via Unified Diagnostics Services (UDS) over the Controller Area Network (CAN).
TEST-RESET_RADC
Tests for power, connection, and communication of the radiator and condenser fan controlled by the Front Vehicle Controller (VCFRONT2).
TEST-SELF_VCFRONT2_X_FAN-RADIATOR-CONDENSER
Tests for power, connection, and communication of the radiator and condenser fan controlled by the Front Vehicle Controller (VCFRONT).
TEST-SELF_VCFRONT_X_FAN-RADIATOR-CONDENSER
Tests the radio tuner for power and connection. Communication is established via the FM antenna (coaxial).
PING-BASH_TUNER
Restraint Control Module (RCM) learns the Whole Vehicle Type Approval (WVTA) string mapping via Gateway (GTW) configurations.
PROC_RCM_X_LEARN-WVTA-FROM-CONFIGS
Arms the Restraints Control Module (RCM)
PROC_RCM_ARM
Configures the Restraint Control Module (RCM) airbags, sensors, and interfaces.
PROC_RCM_X_BOL-CONFIGURATION
Resets the Restraint Control Module (RCM) configuration back to factory default. The RCM must be configured afterwards.
PROC_RCM_X_DEFAULT-BEGINNING-OF-LINE-CONFIGURATION
Clears Diagnostic Trouble Codes (DTCs) in the Restraints Control Module (RCM) Electronic Control Unit (ECU). Checks whether DTCs are set again.
TEST-DTC_RCM
Runs all required routines after a Restraints Control Module (RCM) replacement and arms the system.
PROC_RCM_X_SERVICE-TASKS
Resets the Restraints Control Module (RCM) Electronic Control Unit (ECU) via UDS.
TEST-RESET_RCM
Pressurizes the Front brake circuits from RCU motor.
PROC_RCU_BLEED-CALIPER
Read RCU external pedal travel sensor values (EOL, raw, SENT)
TEST-SELF_RCU_READ-PEDAL-TRAVEL-SENSOR
Read RCU pressure sensor values (EOL, raw, SENT)
TEST-SELF_RCU_READ-PRESSURE-SENSOR
Resets the Redundant Control Unit (RCU) Electronic Control Unit (ECU). Reset is executed via Unified Diagnostics Services (UDS) over the Controller Area Network (CAN).
TEST-RESET_RCU
Re-enables the rear defrost controlled by the Right Vehicle Controller (VCRIGHT).
PROC_VCRIGHT_REAR_DEFROST-RE-ENABLE
The procedure reads the drive inverter rotation in the Right Drive Inverter (DIR) Electronic Control Unit (ECU).
PROC_DIR_X_READ-DI-ROTATIONS