Find the procedure. Understand what it does.
Explore diagnostic tests and repair tasks you can run with Tesware on compatible vehicles.
1,357
service tasks
Model 3, Y, S & X
857 tasks Showing 241–264
Clear filtersErases the Tire Pressure Monitoring System (TPMS) Sensor ID and enables Factory Autolearn.
PROC_VCSEC_X_TPMS-ERASE-AND-AUTOLEARN
Clears Diagnostic Trouble Codes (DTC) in the Electronic Stability Program (ESP) Electronic Control Unit (ECU).
PROC_ESP_X_CLEAR-DTCS
Tests the communication of the Electronic Stability Program (ESP) Electronic Control Unit (ECU). Communication is established via Unified Diagnostics Services (UDS) over the chassis Controller Area Network (CAN).
PING-TP_ESP
Tests the communication of the Electronic Stability Program (ESP) Electronic Control Unit (ECU). Communication is established over the Party Controller Area Network (CAN).
PING-DTC_ESP_X_PARTY
Resets the Electronic Stability Program (ESP) Electronic Control Unit (ECU). Reset is executed via Unified Diagnostics Services (UDS) over the Controller Area Network (CAN).
TEST-RESET_ESP
Write VIN to ETC and generate secret key
PROC_VCLEFT_ETC-LEARN-KEY
Tests for power, connection, and communication of the evaporator thermal expansion valve (TXV) controlled by the Front Vehicle Controller (VCFRONT).
TEST-SELF_VCFRONT_X_EVAP-SOLENOID
Allows the Infotainment and Connectivity ECU (ICE) to exit dyno mode for authorized testing of vehicles on a lift or a dyno.
PROC_ICE_X_EXIT-DYNO-MODE
The procedure allows Infotainment and Connectivity ECU (ICE) to exit factory mode.
PROC_ICE_X_EXIT-FACTORY-MODE
Exits headlamp calibration mode on the selected side(s).
PROC_VC_X_EXIT-HEADLAMP-CALIBRATION-MODE
Exits Service Mode on the vehicle's User Interface (UI). If either Service Mode or Service Mode Plus is currently active, the vehicle returns to normal operation. If neither are active, this routine has no effect.
PROC_ICE_X_EXIT-SERVICE-MODE
Exits Service Mode Plus on the vehicle's touchscreen. If Service Mode Plus is currently active, the vehicle will return to Service Mode and the user will be logged out of the car computer. If Service Mode Plus is not currently active, this routine has no effect.
PROC_ICE_X_EXIT-SERVICE-MODE-PLUS
Exits Override Mode on the speed and torque limit from Factory or Service Mode.
PROC_ICE_X_EXIT-LIMIT-OVERRIDE
The procedure exits Transport Mode on the vehicle's user interface (UI). This mode is used to optimize energy usage and connectivity during transportation. Once delivered, a vehicle should never be in Transport Mode.
PROC_ICE_X_EXIT-TRANSPORT-MODE
Routine will fail if car is DC charging or battery SOC is below 20 percent. Recommend to run test with battery SOC above 40 percent.
TEST-SELF_VCRIGHT_X_EXTENDED-HEAT-PUMP-SYSTEM
Checks the electrical connection between the external amplifier and external microphone.
TEST-BASH_SPK-BASE_X_PED-WARN
Runs the factory Drive Inverter (DI) Odometer initialization routine.
PROC-DID_DI_VEHICLE-ODOMETER
Checks the odometer value and verifies that it is not too high for delivery.
TEST_DI_VEHICLE-ODOMETER-CHECK
Checks fascia camera connection and performs camera firmware update.
PING-HTTP_DAS_X_FASCIA-CAMERA-SCRIPT
The procedure provides access to the audio recordings captured using Service Mode Plus. Note: If the download does not start after selecting "Download Diagnostic Audio", make sure "Insecure content" is set to "Allow" in the site settings.
PROC_ICE_X-FETCH-DIAGNOSTIC-AUDIO-RECORDINGS
Checks the update process of the Infotainment and Connectivity ECU (ICE) updater.
TEST-BASH_ICE_X_CHECK-UPDATE-PROGRESS
Restarts the firmware updater service on the infotainment system.
PROC_ICE_X_RESTART-UPDATER
Tests the electrical connection of the fisheye camera controlled by the Drivers Assistance System (DAS) Electronic Control Unit (ECU).
PING-HTTP_DAS_X_FISHEYE-CAMERA
Tests fisheye camera connection and performs camera firmware update.
PING-HTTP_DAS_X_FISHEYE-CAMERA-SCRIPT