Left electronic parking brake alerts

EPBL alert codes

Showing 101–150 of 169

• EPBL_a177 — Csm Apply Retry EPBL_a177_csmApplyRetry Electronic Parking Brake apply was interrupted. Apply will be retried.
• EPBL_a178 — Caliper State Unknown EPBL_a178_caliperStateUnknown Electronic Parking Brake was not able to determine caliper state on boot.
• EPBL_a179 — Epb Problem EPBL_a179_epbProblem Customer facing alert for Electronic Parking Brake issues which occur when caliper is not moving
• EPBL_a180 — Dynamic Active EPBL_a180_dynamicActive Customer facing alert issued when Electronic Parking Brake is applied at higher than 5mph
• EPBL_a181 — Too Steep Grade To Park EPBL_a181_TooSteepGradeToPark Road grade is too steep to secure with Park Brake
• EPBL_a182 — One EPB Applied Unsec Env EPBL_a182_OneEPBAppliedUnsecEnv One Electronic Parking Brake (EPB) not applied, and road grade is too steep to secure vehicle with only one EPB
• EPBL_a183 — Cdp Not Available EPBL_a183_cdpNotAvailable Stability Control reports Controlled Deceleration for Parking Brake is not available when car is in DRIVE
• EPBL_a184 — Dynamic Park Abort EPBL_a184_dynamicParkAbort Non-nominal termination of dynamic park
• EPBL_a185 — Summon Aborted EPBL_a185_summonAborted
• EPBL_a186 — External Park Abort EPBL_a186_externalParkAbort Non-nominal termination of external park
• EPBL_a187 — Cdp Dynamic EPBL_a187_cdpDynamic Stability Control has begun Controlled Deceleration for Parking Brake
• EPBL_a188 — Epb Dynamic EPBL_a188_epbDynamic Electronic Parking Brake is performing dynamic apply
• EPBL_a189 — Epb Dynamic Park Canceled EPBL_a189_epbDynamicParkCanceled Electronic Parking Brake was attempting to dynamic park, Controlled Deceleration for Parking Brake is unavailable, and speed crossed above 8.8kph
• EPBL_a190 — Csm Apply Degraded EPBL_a190_csmApplyDegraded Electronic Parking Brake apply failed.
• EPBL_a191 — Csm Release Degraded EPBL_a191_csmReleaseDegraded Electronic Parking Brake was unable to release fully.
• EPBL_a195 — Park For Driver Is Leaving EPBL_a195_parkForDriverIsLeaving The Electronic Parking Brake (EPB) reports the driver is leaving and parks the vehicle.
• EPBL_a196 — Free Roll Mode Active EPBL_a196_freeRollModeActive will prevent EPB from parking when the driver leaves
• EPBL_a197 — Free Roll Mode At Speed EPBL_a197_freeRollModeAtSpeed If vehicle reaches 8.8kph, EPB will park
• EPBL_a198 — Hold Clamp Complete EPBL_a198_holdClampComplete EPB hold clamp finished, log I, V, and calculated R
• EPBL_a200 — Pm Unpark Not Allowed EPBL_a200_PmUnparkNotAllowed DI requested unpark but PM didn't allow it
• EPBL_a202 — Remote Epb Config Incompatible EPBL_a202_remoteEpbConfigIncompatible EPB's brake HW config is not compatible remote EPB's brake HW config
• EPBL_a203 — Hw Brake Type Mismatch EPBL_a203_hwBrakeTypeMismatch Electronic Parking Brake's learned configuration does not match the reported config from the gateway
• EPBL_a210 — Park For Driver Is Leaving Debug EPBL_a210_parkForDriverIsLeavingDebug The Electronic Parking Brake (EPB) reports the driver is leaving and parks the vehicle.
• EPBL_a216 — SPI MIA debug Data1 EPBL_a216_SPI_MIA_debugData1 The communication link between Electronic Parking Brake and Electronic Parking Brake Monitor has encountered an error.
• EPBL_a217 — SPI MIA debug Data2 EPBL_a217_SPI_MIA_debugData2 The communication link between Electronic Parking Brake and Electronic Parking Brake Monitor has encountered an error.
• EPBL_a225 — Epb Active Decel EPBL_a225_epbActiveDecel Stability Control has begun Controlled Deceleration for Parking Brake
• EPBL_a241 — Di Output Locked EPBL_a241_diOutputLocked A request to change the DI power state has been denied.
• EPBL_a242 — Hv Output Locked EPBL_a242_hvOutputLocked A request to change the HVC or Contactor power state has been denied.
• EPBL_a243 — Bdw Unavailable EPBL_a243_bdwUnavailable Brake Disc Wipe algorithm is not running due to loss of input signal(s)
• EPBL_a244 — Winch Mode Active EPBL_a244_WinchModeActive Non user facing alert set for service set when winch mode is active
• EPBL_a245 — Service Mode Active EPBL_a245_serviceModeActive User facing to warn that Electronic Parking Brake is in service mode and many Electronic Parking Brake features are disabled
• EPBL_a246 — Idle Fault Apply EPBL_a246_idleFaultApply Electronic Parking Brake apply failed due to idle fault
• EPBL_a247 — Csm Dynamic Apply Retry EPBL_a247_csmDynamicApplyRetry Electronic Parking Brake apply was interrupted during dynamic apply. Apply will be retried.
• EPBL_a248 — Csm Dynamic Apply Failed EPBL_a248_csmDynamicApplyFailed Electronic Parking Brake apply was interrupted during dynamic apply. Apply failed.
• EPBL_a249 — Idle Fault Release EPBL_a249_idleFaultRelease Electronic Parking Brake release failed due to idle fault
• EPBL_a250 — Winch Mode Canceled EPBL_a250_WinchModeCanceled Electronic Parking Brake has detected a vehicle speed condition that caused it to exit winch mode.
• EPBL_a251 — Current Variance High EPBL_a251_currentVarianceHigh Electronic Parking Brake noticed very noisy current
• EPBL_a252 — Winch Mode Pending EPBL_a252_winchModePending Electronic Parking Brake is preparing to enter winch mode
• EPBL_a253 — Esm Release Blocked EPBL_a253_esmReleaseBlocked Electronic Parking Brake is preventing calipers from opening
• EPBL_a254 — Show Stalk Park Button Fault On Ui EPBL_a254_showStalkParkButtonFaultOnUi Electronic Parking Brake has determined that the drive stalk park button has faulted and UI alert should be set allowing driver to park through UI
• EPBL_a256 — Epb System Apply EPBL_a256_epbSystemApply EPB parked the vehicle for a system reason
• EPBL_a261 — Winch Mode Without Steering EPBL_a261_winchModeWithoutSteering The Electronic Parking Brake (EPB) enabled Winch Mode but did not receive the expected messages from the steering system.
• EPBL_a262 — Cannot Prepare Winch Mode EPBL_a262_cannotPrepareWinchMode Non user facing alert set when user attempts to enter winch mode but a system reason prevents EPB from activating winch mode
• EPBL_a263 — Epb Recovery Park EPBL_a263_epbRecoveryPark The Electronic Parking Brake (EPB) attempted to park to establish vehicle security for Low Voltage system recovery.
• EPBL_a264 — Winch Mode Deactivated EPBL_a264_winchModeDeactivated Non user facing alert set when winch mode deactivates
• EPBL_a272 — Vhcl Pwr State Msmtch EPBL_a272_vhclPwrStateMsmtch Vehicle attempted a power state transition which the Electronic Parking Brake did not agree with.
• EPBL_a300 — Left Right Confusion EPBL_a300_leftRightConfusion Electronic Parking Brake not sure if it is a left or a right.
• EPBL_a301 — Ooc Speed Violation EPBL_a301_oocSpeedViolation Vehicle speed is limited based on ultrasonic distance measurements. Currently in ghosted alert.
• EPBL_a302 — Csm Long Release EPBL_a302_csmLongRelease EPB releases no-load is measured using derivative of current. Currently in ghosted alert.
• EPBL_a303 — Clamping Occured Early EPBL_a303_clampingOccuredEarly When EPB was applying the current measured went above the max no load current before piston position estimate predicted it would.