Front passenger door control module alerts

BCFPM alert codes

Showing 51–100 of 123

• BCFPM_a053 — PFDIO Init BCFPM_a053_PFDIOInit
• BCFPM_a054 — PFDIO Process Data BCFPM_a054_PFDIOProcessData
• BCFPM_a055 — PFD Set State BCFPM_a055_PFDSetState
• BCFPM_a056 — Mirror Heat Error BCFPM_a056_MirrorHeatError
• BCFPM_a057 — Reflector Lamp BCFPM_a057_ReflectorLamp
• BCFPM_a058 — Input R High Sync Debug BCFPM_a058_inputRHighSyncDebug Voltage drop on input power is high
• BCFPM_a059 — Input Resistance High BCFPM_a059_inputResistanceHigh A large voltage drop is detected in the input power to the vehicle controller, indicating the resistance on the input power feed to the vehicle controller is higher than expected.
• BCFPM_a060 — Engineering Build BCFPM_a060_engineeringBuild The software installed on the vehicle is intended for engineering use and development purposes only. The vehicle software may have some expected features disabled for testing purposes, or include new features whose function is not yet full…
• BCFPM_a061 — X CP Connected BCFPM_a061_XCPConnected Indicates an active connection to the universal measurement and calibration protocol state machine
• BCFPM_a062 — X CP Was Connected BCFPM_a062_XCPWasConnected Indicates there was an active connection to the universal measurement and calibration protocol state machine
• BCFPM_a063 — Switch Fault BCFPM_a063_SwitchFault A condition affecting switch functionality has been detected.
• BCFPM_a064 — Bus Sleep Req Timeout BCFPM_a064_busSleepReqTimeout Indicates if a bus has timed out of a sleep request from the network manager
• BCFPM_a065 — Ratcheting Detected BCFPM_a065_ratchetingDetected
• BCFPM_a066 — False Latch Cinch BCFPM_a066_falseLatchCinch Not to be confused with a weak cinch. This alert does not imply problems with seal load or door alignment.
• BCFPM_a067 — Missed Short Drop BCFPM_a067_missedShortDrop The body controller will automatically re-issue a short-drop command if a failure to drop is detected.
• BCFPM_a068 — Missed Undrop BCFPM_a068_missedUndrop The body controller will automatically re-issue an undrop command if a failure to undrop is detected.
• BCFPM_a069 — Latch Status Ignored BCFPM_a069_LatchStatusIgnored This alert probably indicates that a firmware bug was encountered. Resetting the front door body controller will temporarily resolve the issue.
• BCFPM_a070 — Latch Failed To Cinch BCFPM_a070_LatchFailedToCinch The door latch cinching actuation completed but the latch is not fully closed.
• BCFPM_a071 — Latch Failed To Release BCFPM_a071_LatchFailedToRelease The door latch release actuation completed but the latch is not OPENED.
• BCFPM_a072 — Unexpect Latch Closed BCFPM_a072_UnexpectLatchClosed The door latch is closed while the door angle is outside the latch closing zone.
• BCFPM_a073 — Unexpect Latch Open BCFPM_a073_UnexpectLatchOpen The door latch transitions to open state unexpectedly.
• BCFPM_a074 — No Latch Entry On Close BCFPM_a074_NoLatchEntryOnClose The front door latch did not detect the striker after the door ramped up to engage the latch.
• BCFPM_a075 — Door Ice Breaker Attempt BCFPM_a075_DoorIceBreakerAttempt The door ice breaker is requested to extend following unsuccessful latch release attempts.
• BCFPM_a076 — Door Ice Breaker Failure BCFPM_a076_DoorIceBreakerFailure The door ice breaker extended but the door latch is not opened.
• BCFPM_a077 — Latch Mech Release Stuck BCFPM_a077_LatchMechReleaseStuck Often caused by a kinked release cable or damaged cable tubing
• BCFPM_a078 — Door Unzeroed BCFPM_a078_DoorUnzeroed The door zero position is cleared.
• BCFPM_a079 — Dvr Side Cfg Mismatch BCFPM_a079_DvrSideCfgMismatch reseting the controller should fix the issue
• BCFPM_a080 — Current Drop Out BCFPM_a080_CurrentDropOut
• BCFPM_a081 — Latch Open In Motion BCFPM_a081_LatchOpenInMotion The door latch transitions to opened state while the vehicle is in motion.
• BCFPM_a082 — Door Zeroed BCFPM_a082_doorZeroed For engineering diagnoses only
• BCFPM_a083 — Unexpected Stop BCFPM_a083_UnexpectedStop The door stopped unexpectedly while opening or closing.
• BCFPM_a084 — Release End Stop BCFPM_a084_ReleaseEndStop
• BCFPM_a085 — ESP Gyro Unstable BCFPM_a085_ESPGyroUnstable
• BCFPM_a086 — Bad ESP Data BCFPM_a086_badESPData
• BCFPM_a087 — Mirr Tilt Test Failure BCFPM_a087_MirrTiltTestFailure This alert exists purely to provide diagnostic information for FW development. Because this alert is triggered only as part of the mirror tilt test routine, it is not expected to occur as part of customer use.
• BCFPM_a088 — V2 Door Brake Cal Pos BCFPM_a088_V2DoorBrakeCalPos This alert exists purely to provide diagnostic information for FW development.
• BCFPM_a089 — V2 Door Brake Cal Neg BCFPM_a089_V2DoorBrakeCalNeg This alert exists purely to provide diagnostic information for FW development.
• BCFPM_a090 — Crash Unlock Error BCFPM_a090_CrashUnlockError
• BCFPM_a091 — Crash State Mismatch BCFPM_a091_CrashStateMismatch
• BCFPM_a092 — Hill Hold BCFPM_a092_HillHold Door applying torque to hold on hill
• BCFPM_a093 — OTP Error BCFPM_a093_OTPError Check OTP region of DFLASH
• BCFPM_a094 — Ice Breaker Retract BCFPM_a094_iceBreakerRetract Debug alert logging icebreaker operational metrics after the icebreaker completed a retracting actuation.
• BCFPM_a105 — ECU Debug Mode BCFPM_a105_ECUDebugMode Production vehicle should not have Debug Jumper in place. Remove jumper from ECU.
• BCFPM_a108 — Latch Release Error BCFPM_a108_LatchReleaseError Check alertLog for more information. If resultingState is CLOSED_BRAKE, the latch's OPEN switch may be disconnected. If previousState is OPENED_BRAKE, the latch's switches and release motor may be all disconnected.
• BCFPM_a109 — Door Brake Uncalibrated BCFPM_a109_DoorBrakeUncalibrated The door motor brake is not calibrated and using default values.
• BCFPM_a110 — PFD Linkage Fault BCFPM_a110_PFDLinkageFault The linkage may have become detached at the ball joint. This alert is only present in factory mode.
• BCFPM_a111 — Latch Release Error BCFPM_a111_LatchReleaseError Check alertLog for more information. If resultingState is CLOSED_BRAKE, the latch's OPEN switch may be disconnected. If previousState is OPENED_BRAKE, the latch's switches and release motor may be all disconnected.
• BCFPM_a112 — Mirror Position BCFPM_a112_MirrorPosition
• BCFPM_a113 — Mirror Memory BCFPM_a113_MirrorMemory
• BCFPM_a114 — Mirror Folding BCFPM_a114_MirrorFolding