Find the procedure. Understand what it does.
Explore diagnostic tests and repair tasks you can run with Tesware on compatible vehicles.
1,357
service tasks
Model 3, Y, S & X
421 tasks Showing 289–312
Clear filtersThis tests verifies whether the rain/light sensor is functional by observing the auto headlamps and day/night display modes. Make sure the headlights and display modes are both set to AUTO.
TEST_RLS_X_LIGHT-TEMPERATURE-VENDOR
Arms the Restraints Control Module (RCM)
PROC_RCM_ARM
Clears Diagnostic Trouble Codes (DTCs) in the Restraints Control Module (RCM) Electronic Control Unit (ECU). Checks whether DTCs are set again.
TEST-DTC_RCM
This routine will re-enable pack contactors by clearing BMS_w/f026_SW_Ctrs_Disabled. This routine should only be executed after identifying/resolving the reason for pack contactors being disabled (i.e. Charger detecting crash event, HWOC, welded contactor, etc.).
PROC_BMS_X_ENABLE-CONTACTORS
Read specified file from the infotainment filesystem.
TEST-BASH_ICE_X_READ-FILE
The procedure returns ride height calibration offset values for Tesla Air Suspension (TAS).
PROC_TAS_X_READ-RIDE-HEIGHT-CALIBRATION
Calibrates the rear driver door handle by actuating the fork to its maximum and minimum positions. If needed, the routine configures the door handle controller to learn its location.
PROC_DHRD_REAR-DRV_DOOR-HANDLE-CALIBRATION
Enables only the rear motor on a dual motor vehicle with All-Wheel Drive (AWD). Vehicle will operate with only the rear motor. To run this procedure, vehicle must be four wheel drive and satisfy either GUI_isDevelopmentCar, GUI_factoryMode, or GUI_serviceMode.
PROC_ICE_X_REARONLY-MOTOR-MODE
Calibrates the rear passenger door handle by actuating the fork to its maximum and minimum positions. If needed, the routine configures the door handle controller to learn its location.
PROC_DHRP_REAR-PAS_DOOR-HANDLE-CALIBRATION
This check verifies that the rear defrost grid is heating when it is commanded on.
PROC_CID_REAR_WINDOW-DEFROST
Records a new maintenance or repair event for this vehicle, adding to its service history database.
PROC_ICE_X_RECORD-SERVICE-ACTION
Reformat the gen2 gateway sd card and reboot the mcu. Task will not run if display is on or a software update is in progress.
PROC_ICE_X_FORMAT-GTW2-SD
Resets remote unlock security key on body controller.
PROC_ICE_X_RESET-REMOTE-KEY
Provides RMI (Repair and Maintenance Information) Vitals values, including configuration values, alerts, and data.
PROC_ICE_X_RMI-VITALS
Requests the accessory rail and the drive rail to power off.
PROC_CID_X_REQUEST-RAILS-OFF
Requests the drive rail to power off and the high voltage battery pack contactors to open.
PROC_CID_X_REQUEST-HV-CONTACTORS-OPEN
Turns the drive rail off and attempts to reset all fuses on the EFUSE board.
PROC_EFUSE_X_RESET-EFUSES
Send a hard reset ECU command to the BCCEN
TEST-RESET_BCCEN
This routine resets all HV battery brick calculated amp-hour capacities (CACs) to their nominal/default values. During normal operation, the BMS calculates brick CAC values over multiple charge/discharge cycles. In the event of a large accumulated error, this routine can reset the calculated CAC based solely on the nominal/default brick CAC values to improve the BMS' full pack energy prediction.
PROC_BMS_X_RESET-CAC
Send a hard reset ECU command to the DI
TEST-RESET_DI
Turns the drive rail off and attempts to reset EFUSE ECU.
PROC_DAS_X_EFUSE-RESET
The procedure resets the User Interface (UI) firmware update progress state.
PROC_ICE_X_RESET-UPDATE-PROGRESS
Send a reset ECU command to the LFT (Liftgate controller)
TEST-RESET_LFT
CAUTION: reset remote unlock security key on body controller ONLY if remoteAccessRejected alert has fired recently.
PROC_ICE_X_RESET-REMOTE-KEY-SERVICE