iBooster brake booster alerts
Browse 256 IBST alert codes and open an entry for its description and recorded conditions.
IBST alert codes
Showing 201–250 of 256
- IBST_a201 — EGGREAR1 wheel Speeds Rear Time Out IBST_a201_EGGREAR1wheelSpeedsRearTimeOut CAN communication timeout error with EGGREAR1
- IBST_a202 — EGGREAR1 wheel Speeds Rear Checksum IBST_a202_EGGREAR1wheelSpeedsRearChecksum CAN communication checksum error with EGGREAR1
- IBST_a203 — EGGREAR1 wheel Speeds Rear DLC IBST_a203_EGGREAR1wheelSpeedsRearDLC CAN communication data length error with EGGREAR1
- IBST_a204 — EGGREAR1 wheel Speeds Rear Counter IBST_a204_EGGREAR1wheelSpeedsRearCounter CAN communication counter error with EGGREAR1
- IBST_a205 — EGGRIGHT1 wheel Speeds Front Time Out IBST_a205_EGGRIGHT1wheelSpeedsFrontTimeOut CAN communication timeout error with EGGRIGHT1
- IBST_a206 — EGGRIGHT1 wheel Speeds Front Checksum IBST_a206_EGGRIGHT1wheelSpeedsFrontChecksum CAN communication checksum error with EGGRIGHT1
- IBST_a207 — EGGRIGHT1 wheel Speeds Front DLC IBST_a207_EGGRIGHT1wheelSpeedsFrontDLC CAN communication data length error with EGGRIGHT1
- IBST_a208 — EGGRIGHT1 wheel Speeds Front Counter IBST_a208_EGGRIGHT1wheelSpeedsFrontCounter CAN communication counter error with EGGRIGHT1
- IBST_a209 — Reduced Brake Power Active IBST_a209_reducedBrakePowerActive Peak brake power is limtied to protect low voltage system.
- IBST_a210 — Reduced Brake Power Not Available IBST_a210_reducedBrakePowerNotAvailable iBooster is unable to accomadate the request to reduce peak power.
- IBST_a211 — DET Report Error IBST_a211_DETReportError Single failure word for all DET reported errors has been set. This error is expected to only occur in XCP unit
- IBST_a212 — Info Failure Wrong CUBAS Handling Detected IBST_a212_infoFailureWrongCUBASHandlingDetected Diagnostic Application Callback Handler information failure for indication of wrong callback handling of CUBAS stack
- IBST_a213 — PDU Routerinitialization Failed IBST_a213_PDURouterinitializationFailed PDU Router initialization failed (PDU Router changed to PDUR_REDUCED state).
- IBST_a214 — Loss Of PDU Instance Detected IBST_a214_LossOfPDUInstanceDetected Loss of a PDU instance (FIFO flushed because of an overrun)
- IBST_a215 — Unsupported Series HW Detected IBST_a215_UnsupportedSeriesHWDetected iBooster has detected hardware is not allowed in a series ECU.
- IBST_a216 — Asic Malfunction Detected IBST_a216_AsicMalfunctionDetected On the system ASIC an overcurrent event occured. The General Purpose Input Output (GPIO) is malfunctioning
- IBST_a217 — Asic Trimming Not Completed IBST_a217_AsicTrimmingNotCompleted iBooster has detected System ASIC trimming is not completed
- IBST_a218 — U C Safety Notification GRAM IBST_a218_uCSafetyNotificationGRAM Microcontroller memory guard has detected a GRAM guard violation event.
- IBST_a219 — U C Safety Notification IBST_a219_uCSafetyNotification Microcontroller memory/peripheral guard has detected a violation event by an unauthorized busmaster.
- IBST_a220 — AS IC Overcurrent On GPIO250 2 IBST_a220_ASICOvercurrentOnGPIO250_2 On the system ASIC an overcurrent event occured on General Purpose Input Output (GPIO) 250_2
- IBST_a221 — AS IC Overcurrent On GPIO250 1 IBST_a221_ASICOvercurrentOnGPIO250_1 On the system ASIC an overcurrent event occured on General Purpose Input Output (GPIO) 250_1
- IBST_a222 — AS IC Overcurrent On GPIO50 4 IBST_a222_ASICOvercurrentOnGPIO50_4 On the system ASIC an overcurrent event occured on General Purpose Input Output (GPIO) 50_4
- IBST_a223 — AS IC Overcurrent On GPIO50 3 IBST_a223_ASICOvercurrentOnGPIO50_3 On the system ASIC an overcurrent event occured on General Purpose Input Output (GPIO) 50_3
- IBST_a224 — AS IC Overcurrent On GPIO50 2 IBST_a224_ASICOvercurrentOnGPIO50_2 On the system ASIC an overcurrent event occured on General Purpose Input Output (GPIO) 50_2
- IBST_a225 — AS IC Overcurrent On GPIO50 1 IBST_a225_ASICOvercurrentOnGPIO50_1 On the system ASIC an overcurrent event occured on General Purpose Input Output (GPIO) 50_1
- IBST_a226 — AS IC Overcurrent On WRHS IBST_a226_ASICOvercurrentOnWRHS On the system ASIC an overcurrent event occured on WRHS
- IBST_a227 — Wake Request Mismatch Detected IBST_a227_wakeRequestMismatchDetected iBooster has detected a wake request mismatch between wakeline and CAN command signal
- IBST_a228 — Blocked Pedal Detected During HAD IBST_a228_BlockedPedalDetectedDuringHAD Pedal movement was blocked during highly autonomous driving braking
- IBST_a229 — Blocked Pedal Detected IBST_a229_BlockedPedalDetected Pedal movement was blocked during autonomous driving braking
- IBST_a230 — DTS2 Functional Range Low IBST_a230_DTS2FunctionalRangeLow The differential travel signal (channel 2) is out of its functional range low
- IBST_a231 — DTS2 Functional Range Low IBST_a231_DTS2FunctionalRangeLow The differential travel signal (channel 2) is out of its functional range high
- IBST_a232 — Post Assembly Routine Failed IBST_a232_PostAssemblyRoutineFailed Plausibility check of DTS signals (Magnetic field strength and stroke signal) after iBooster assembly process
- IBST_a233 — Reference Run Abort By ECU Reset IBST_a233_ReferenceRunAbortByECUReset Reference Run not completed successively due to ECU Resets when iBooster shutting down
- IBST_a234 — Li PS Out Of Range High IBST_a234_LiPSOutOfRangeHigh iBooster's Linear Position Sensor has detected out of Range High
- IBST_a235 — Li PS Out Of Range Low IBST_a235_LiPSOutOfRangeLow iBooster's linear position sensor has detected out of range low
- IBST_a246 — DAS redundant Braking Control Party Checksum IBST_a246_DASredundantBrakingControlPartyChecksum Checksum error detected on Driver Assistance System (DAS) checksum signal DAS_redundantBrakingControlChecksum on PARTY CAN bus.
- IBST_a247 — DAS redundant Braking Control Party Counter IBST_a247_DASredundantBrakingControlPartyCounter Alive counter error detected on Driver Assistance System (DAS) alive counter signal DAS_redundantBrakingControlCounter on PARTY CAN bus.
- IBST_a248 — DAS redundant Braking Control Party DLC IBST_a248_DASredundantBrakingControlPartyDLC Data length code error detected on Driver Assistance System (DAS) message DAS_redundantBrakingControl.
- IBST_a249 — DAS redundant Braking Control Party Timeout IBST_a249_DASredundantBrakingControlPartyTimeout Driver Assistance System (DAS) message DAS_redundantBrakingControl not received within expected time frame on PARTY CAN bus.
- IBST_a250 — DAS redundant Braking Control Chassis Checksum IBST_a250_DASredundantBrakingControlChassisChecksum Checksum error detected on Driver Assistance System (DAS) checksum signal DAS_redundantBrakingControlChecksum on CH CAN bus.
- IBST_a251 — DAS redundant Braking Control Chassis Counter IBST_a251_DASredundantBrakingControlChassisCounter Alive counter error detected on Driver Assistance System (DAS) alive counter signal DAS_redundantBrakingControlCounter on CHASSIS CAN bus.
- IBST_a252 — DAS redundant Braking Control Chassis DLC IBST_a252_DASredundantBrakingControlChassisDLC Data length code error detected on Driver Assistance System (DAS) message DAS_redundantBrakingControl.
- IBST_a253 — DAS redundant Braking Control Chassis Timeout IBST_a253_DASredundantBrakingControlChassisTimeout Driver Assistance System (DAS) message DAS_redundantBrakingControl not received within expected time frame on CHASSIS CAN bus.
- IBST_a254 — DI loc Status2 Checksum IBST_a254_DIlocStatus2Checksum Checksum error detected on Drive Inverter (DI) checksum signal DI_locStatus2Checksum.
- IBST_a255 — DI loc Status2 Counter IBST_a255_DIlocStatus2Counter Alive counter error detected on Drive Inverter (DI) alive counter signal DI_locStatus2Counter.
- IBST_a256 — DI loc Status2 DLC IBST_a256_DIlocStatus2DLC Data length code error detected on Drive Inverter (DI) message DI_locStatus2.
- IBST_a257 — DI loc Status2 Timeout IBST_a257_DIlocStatus2Timeout Drive Inverter (DI) message DI_locStatus2 not received within expected time frame.
- IBST_a258 — Standalone EBR Active IBST_a258_standaloneEBRActive External Brake Request (EBR) is active using iBooster only without ESP. This feature manages the brake commands for Autopilot and vehicle comfort features, such as vehicle hold. Can only be set during autonomous operation
- IBST_a259 — EMC Main11 Checksum IBST_a259_EMCMain11Checksum Checksum error detected on Electronic Stability Program (ESP) checksum signal ESP_EMCMain11Checksum.
- IBST_a260 — EMC Main11 Counter IBST_a260_EMCMain11Counter Alive counter error detected on Electronic Stability Program (ESP) alive counter signal ESP_EMCMain11Counter.